1、Battery Connection Board SpecificationPROPRIETARY & CONFIDENTIALFOR INTERNAL USE ONLYThis document may not be copied, disclosed, or used in whole or in part without the consent of COVIDIEN. 2008 COVIDIEN All Rights Reserved.COVIDIEN6135 Gunbarrel AvenueBoulder, CO 80301 Proprietary and ConfidentialT

2、ITLE:Battery Connection Board SpecificationDOCUMENT NUMBER10024249SHEET 1 of 7REVCREVISIONREVDESCRIPTIONCRELEASE/CHANGE PER ECO-R172706Table of Contents1.0INTRODUCTION3Purpose3Scope3Revision History3Glossary / Acronyms3OVERVIEW3Electrical Requirements4Specifications4Interconnects2.03.04.04

3、.4.2.2Power Management Connector (J1)4Battery Connector55.0Mechanical Requirements6Size6Mounting6Cooling6Fabrication6Protection6Labeling7Packaging Requirements6.0PROPRIETARY & CONFIDENTIALFOR INTERNAL USE ONLYThis document may not be copied, disclosed, or used in whole or

4、 in part without the consent of COVIDIEN. 2008 COVIDIEN All Rights Reserved.COVIDIEN6135 Gunbarrel AvenueBoulder, CO 80301 Proprietary and ConfidentialTITLE:Battery Connection Board SpecificationDOCUMENT NUMBER10024249SHEET 2 of 7REVC1.0INTRODUCTIONPurposeThe purpose of this document is to provide t

5、he requirements for the Battery Connection Board.1.11.2ScopeThis document provides the requirements for the Battery Connection Board used in the PB 520, 540, 560, and 640.1.3Revision HistoryRevisionDateAuthorChange DescriptionA11/08/07Initial releaseB11/03/08Clarify requirements, update to standard

6、format.C1/20/009Incorporate updates from Verification Review2.0Glossary / Acronyms3.0OVERVIEWThe Battery Connection Board provides the interconnections between the Power Management Board and the Battery. This PCBA is used in place of a cable or harness. PCBA mounted spring fingers provide a connecti

7、on to the battery cell device and a connector on the PCBA provides the interface to the Power Management PCBA.PROPRIETARY & CONFIDENTIALFOR INTERNAL USE ONLYThis document may not be copied, disclosed, or used in whole or in part without the consent of COVIDIEN. 2008 COVIDIEN All Rights Reserved.COVI

8、DIEN6135 Gunbarrel AvenueBoulder, CO 80301 Proprietary and ConfidentialTITLE:Battery Connection Board SpecificationDOCUMENT NUMBER10024249SHEET 3 of 7REVCAcronymDefinitionAAmperePCBAPrinted Circuit Board AssemblyVVolt4.0Electrical RequirementsSpecificationsHWSBAB7 Traces used to provide battery powe

9、r shall be capable of supporting 3A at 29.4V, reference section .1HWSBAB8 Traces used to provide battery power shall have less than 100mV drop at 3A, reference section 4.2.2.HWSBAB9 The battery connection board shall provide an interconnect to allow measurement of the battery temperature, ref

10、erence section 4.2.2.HWSBAB10 The battery connection board shall provide an interconnect to allow reading of the battery memory device, reference section 4.2.2.HWSBAB11 The battery connector shall support 1mm travel while providing a valid electrical contact between the battery and the Battery Conne

11、ction Board.HWSBAB12 Spring contacts shall be rated for 2X the maximum required current.4.2Interconnects4.2.1Power Management Connector (J1)PROPRIETARY & CONFIDENTIALFOR INTERNAL USE ONLYThis document may not be copied, disclosed, or used in whole or in part without the consent of COVIDIEN. 2008 COV

12、IDIEN All Rights Reserved.COVIDIEN6135 Gunbarrel AvenueBoulder, CO 80301 Proprietary and ConfidentialTITLE:Battery Connection Board SpecificationDOCUMENT NUMBER10024249SHEET 4 of 7REVCPIN NUMBERSIGNAL NAMEPIN NUMBERSIGNAL NAME1-(Battery -)2-(Battery -)3-(Battery -)4-(Battery -)5TEMP6MEM7+(Battery +)

13、8+(Battery +)9+(Battery +)10+(Battery +)4.2.2Battery ConnectorPROPRIETARY & CONFIDENTIALFOR INTERNAL USE ONLYThis document may not be copied, disclosed, or used in whole or in part without the consent of COVIDIEN. 2008 COVIDIEN All Rights Reserved.COVIDIEN6135 Gunbarrel AvenueBoulder, CO 80301 Propr

14、ietary and ConfidentialTITLE:Battery Connection Board SpecificationDOCUMENT NUMBER10024249SHEET 5 of 7REVCConnector DesignationPIN NUMBERSIGNAL NAMEPIN NUMBERSIGNAL NAMEJ31+(Battery +)2+(Battery +)J41MEM (EEPROM)2MEM (EEPROM)J51TEMP (EEPROM)2TEMP (EEPROM)J61-(Battery -)2-(Battery -)5.0Mechanical Req

15、uirementsSizeHWSBAB13 The length (L1) of the PCBA shall be 68mm +/- 1mm HWSBAB14 The length (L2) of the PCBA shall be 43mm +/- 1mm HWSBAB15 The width (W) of the PCBA shall be 45mm +/- 1mm HWSBAB16 The thickness (T) of the PCBA shall be 1.60mm +/- 0.5mm5.1L2WKeep Out8.5 mmL14mm5.2MountingHWSBAB17 Thr

16、ee areas shall be kept clear of traces and feed throughs on the J1 side of the PCBA to allow for mounting. The first area on the top (labeled Keep out) shall have a height of 6mm +/- 1mm and length of 12.5mm +/-1mm. The second area (labelled Keep Out) shall have a length of 4mm +/- 1mm and a height

17、of 8.5mm +/- 1mm.5.3CoolingN/A.5.4FabricationHWSBAB18 The Printed Circuit Board shall be fabricated per standard IPC-A-610D: 2005, Acceptability for Electronic Assemblies Class III5.5ProtectionN/A.PROPRIETARY & CONFIDENTIALFOR INTERNAL USE ONLYThis document may not be copied, disclosed, or used in w

18、hole or in part without the consent of COVIDIEN. 2008 COVIDIEN All Rights Reserved.COVIDIEN6135 Gunbarrel AvenueBoulder, CO 80301 Proprietary and ConfidentialTITLE:Battery Connection Board SpecificationDOCUMENT NUMBER10024249SHEET 6 of 7REVC5.6LabelingHWSBAB19 The PCBA shall be labeled with its Name, Part Number and Revision which is al