1、NOKIA 手機工程模式的說明書簡介：NOKIA 移動電話的工程模式名稱為“ Netmonitor" 分組畫面為改錐、鐵錘和手機，諾基亞的工程模式啟動后可以通過命令開啟或關閉。前面的畫面顯示系統網絡的功能，后面則以介紹手機內軟硬件資料為主。? 載頻號碼、在GSM 系統的范圍是1-124 ；? Carrier number. The range in GSM is 1-124?移動臺接收電平(dBM 值)；? MS RX level in dBM?接收信號等級，在GSM 系統的范圍是0-7 ；? Received signal quality. The range in GSM is

2、0-7? 移動臺發射功率等級，在GSM 系統的范圍是5-15 級；? MS TX power level. The range in GSM is 5-15? C1(多徑衰耗標準)；? C1 (path loss criterion, used for cell selection and reselection, the range in GSM is -99.99)? RLT( 音頻超時)?RLT (Radio Link Timeout)?時隙，在 GSM 系統的范圍是0-7 ；? Timeslot. The range in GSM is 0-7? 發射轉態指示；? Indication

3、 of the transmitter status? 網絡信息；? Information of the network parameteres? TMSI( 臨時移動電話識別碼 ) ；?TMSI (temporary Mobile Subscriber Identity)?小區 ID;? Cell Identification (Cell ID, number of the used cell)? 國家碼；? MCC (Mobile Country Code)? 網絡碼；? MNC (Mobile Network Code)? 本地區域碼；? LAC (Location Area Code

4、)? 地區碼；? Ciphering (on/off)? 調頻；? Hopping (on/off)? 調頻；? DTX (on/off)? 自動功率控制Discarding cell barred information工程模式介紹8/7按左邊確認鍵即可進入工程模式菜單菜單10-1NOKIA| 16 -55 xxx | CH Rx1 Pwr |0 1 x xxxx | TS TA RLT xxxx| 51 51 | Q1 Q1 | CCCH | xxCH |16-表示 BCCH 載頻號碼； means BCCH carrier number-55-表示接收 功率值；means RX leve

5、l (in dBm)xxx-Pwr 表示 發射功率等級； Pwr means TX power level0-時隙；TS (Time Slot)1-時間前置量；顯示手機和基站的距離，乘以500以公尺計算；TA - Timing Advancex-RLT - Radio Link Timeoutxxxx- 不詳；51(C1)-多徑衰耗標準，本人英語和基站知識不靈光，大伙自己體會吧C1 (path loss criterion, used forcell selection and reselection, the range in GSM is -99.99)CCCH -載頻類型之一；(xxCH

6、) type of current channel:AGCH-(Access Grant Channel)允許連接頻道由網絡到手機的單向頻道，安排專用控制信道 以完成連接上網；獨立專用控制信道;* SDCC -(SDCCH:Stand-alone Dedicated Control Channel)* TFR -(TCH:Traffic Channels)業務信道；* BCCH -(Broadcast Control Channel)廣播控制信道；*SEARCH手機正在搜索的網絡信號；* NSPS -(No Service & Power Save),無網絡服務，手機正處于省電模式；通

7、話中CHT項變化：AGCH->SDCC->TFR-掛斷電話->CCCH開機時 CHT項變化:AGCH->SDCC->BCCH->CCCH? AGCH - Access Grant Channel - is the answer to RACH. It's used to assign a mobile a Stand-alone Dedicated Control Channel (SDCCH). It's downlink and point to point channel.? SDCC - (SDCCH) Stand-alone Ded

8、icated Control Channel - It's used for system sygnalling: cell set-up, authentication, location update, assigment to traffic channels and transmission of short messagesTFR - (TCH) Traffic Channels - Physical channels also transfer user data, which can be either in the form of Half Rate traffic (

9、6.5kbit/s) or Full Rate (13kbit/s). Another form of traffic channel is the Enhanced Full Rate (EFR) Traffich Channel. The speech coding in EFR is still dona at 13kbit/s, but the coding mechanism is different than that used for normal full rate traffic. EFR coding gives better speech quality than nor

10、mal full rate. Traffic channels can transmit both speech and data. these are bi-directional channels.BCCH - Broadcast Control Channel contains detailed network and cell specific information such as:o Frequencies used in the particular cell.o Frequency hopping sequence.o Channel Combination. In the G

11、SM there are eleven logical channels. Depending on the number of frequencies used in a cell, the number of physical channels available is eight times the number of used frequecies. most of these physical channels have to be allocated for traffic purposes. There are more than one ways in these aleven

12、 logical channels are mapped on the available physical channels. How they are mapped varies from cell to cell depending on a number of categories. Channel combination tells about the mapping method used in the particular cello Paging groups. Normally in one cell there are more than one paging channe

13、ls. To prevent a mobile to listening to all the paging channels for a paging message, the paging channels are divided such that, a group of mobile stations listen to a particular paging channel only.o Information on surrounding cells. A mobile station has to know what are the cells surrounding the p

14、resent cell and what frequencies are being broadcast on them. This is necessary if, for example, the user initiates a conversation in the current cell, and then decides to move on. The MS has measure the signal strength and quality of the surrounding cells and report to the base station controller.S

15、EARCH Mobile Station is searching for signal.NSPS (No Serv Power Save) 菜單 10-2| NO 7 B49 | 16 x |B49- 蜂窩阻塞( 參考菜單 10-19)16- 信道號x - 發射是為- 0 ，待機時為-1菜單 10-3, 10-4, 10-5|16 50 -56 50| |90 32 -74 32| |17-99 -80-99| | N N|18 19 -87 19|20 18 -88 18|83 15 -89 15|29 13 -93 13|xx xx xx xx|xx xx xx xx|xxx ccc v

16、vv ccc|N N N | N xx xx | | AA AA AAxxx - means BCCH carrier number of the servingcell in decimal instead of BCCH carrier number DCH carrier number will be desplayed in activ mode.vvvAAccc - means C1 value of the neighbour instead of C1 value letter "B" and BSIC value will be desplayed in a

17、ctiv mode.- 表示接收功率等級(dBm)- 普通小區 (N), 阻塞小區 (B).菜單 10-3 Number of serving cell, and 2 neigbours.菜單 10-4 Next 3 neigbours.菜單 10-5 Next 3.菜單10-6|26002 26202|41040 26001|C9E00 xxxxx|21303 xxxxx|看過一些測試項就可看到如下顯示:|26002 26202|00000 26001|11111 xxxxx|33333 xxxxx|手機無法進行編輯，而老的 Alcatel HC 1000可以編輯;D2 Privat net

18、work code.屏幕左邊是予存網絡列表，Nokia 6110262 02-目前注冊使用中的網絡代碼260 01-曾經嘗試登錄被禁用網絡代碼Plus GSM networ code.Menu 10-7|E A H C I BR|1 1 0 1 0 00|E:系統是否支持緊急求救電話即112: 1為支持、0為不支持;A: attach-detach 程序，1為支持，0為不支持；H:是否支持半速率編碼，1為支持，0為不支持；C: C2值廣播，1為支持，0為不支持；I:系統第7、8信息廣播，1為支持，為不支持；B:系統廣播，1為支持，0為不支持；R: re-establishment.1 為支持，

19、0 為不支持； Menu 10-10|TMSI 1620101B|T321 : 1 /30|PRP :6 15 90| | -2 16|TMSIT321臨時移動臺識別碼：Temporary Mobile Subscriber Identity-Counter (min 1, max 240, where 1 means 6 min time between location updates and 240 means 240*6min=24h between location updates).PRP - Paging Repeat Period (range is 2-9, when pag

20、ing is in every second multiframe, mobile takes more current that if it were in every 9th multiframe).16 in the last line is number of serving cell channel.菜單10-11|CC:260 NC:02| | LAC:2419 | CH : 16 | CID:5DE9 |CC - (MCC)移動國家碼；Mobile Country Code (260 - Pland)NC - (MNC) 移動網絡碼 Mobile Network Code (02

21、 - Era GSM)LAC -本地區域識別碼 Location Area CodeCH -使用中載頻號碼 Serving cell channel numberCID -基站編號(Cell ID ) Cell Identifier菜單10-12CIPHER :OFF |HOPPINNG:OFF |DTX : ON |IMSI : ON |CIPHER - ciphering value A51, A52 or OFFHOPPING - 跳頻值 Hopping value - ON/OFFDTX- Discontinuos Transmission (Mechanism)ON/OFFIMSI-

22、 International Mobile Subscriber Identity菜單10-13| NOTALLOWED | xxxxxxxxxxxx | DTX(DEF) :ON | VVVVVVVVVVVV I| DTX(BS) :USE| | zzzzzzzzzzzz |I I IIWith this display is possible to change MS to use DTX or not if BS allows MS to decide it.To change DTX state, You must activate this display from MENU. Wh

23、en MENU is not active and the user is scrollinng field test displays with NEXT and PREVIOUS, the DTX state will not change? xxxxxxxxxxx is status of switched mode. The values are:o DTX ON (MS use DTX)o DTX OFF (MS not use DTX)o DTX DEF (MS use default state of DTX Defined in MS_PAR.H)o NOTALLOWED (B

24、S not allows MS to decide if it uses DTX or not)? yyyyyyyyyyyy is default state of DTX, definned in MS_PAR.H. Values are: oMS DEF: ONoMS DEF: OFF? zzzzzzzzzzzz is DTX value from BS. The values are:oMS MAY USE (BS allows MS to decide if it uses dtx or not on uplinkoSHALL USE (BS controls MS to use dt

25、x (on uplink)SHALL NOT (BS controls MS not to use dtx (on uplink)Menu 10-17| BTS TEST |I OFF IIIIIBTS TEST 狀態開關 ：Swith BTS TEST statusIf ON - Mobile is serching only one frequency. Neigbour mesurements are not doneIf OFF - Mobile is behaving nornally. Neigbour mesurements are doneTo change status from OFF to ONwrite to SIM memory #33 channel number, go to menu 10-17, turn POWER OFF and again ON. Now You have active BTS TEST!Menu 10-19| CELL BARR | CELL BARR | CELL BARR | ACCEPTED | REVERSE| DISC