混凝土基礎的施工技術_第1頁
混凝土基礎的施工技術_第2頁
混凝土基礎的施工技術_第3頁
混凝土基礎的施工技術_第4頁
混凝土基礎的施工技術_第5頁
免費預覽已結束,剩余3頁可下載查看

下載本文檔

版權說明:本文檔由用戶提供并上傳,收益歸屬內容提供方,若內容存在侵權,請進行舉報或認領

文檔簡介

1、混凝土一基礎的施工技術【教材解讀】一、鋼筋工程施工技術要求(1)鋼筋網的綁扎:綁扎時應注意相鄰綁扎點的鋼絲扣要成八字形,以免網片歪斜變形。(2)基礎底板采用雙層鋼筋網時,在上層鋼筋網下面應設置鋼筋撐腳,以保證鋼筋位置 正確。(3)鋼筋的彎鉤應朝上,不要倒向一邊,但雙層鋼筋網的上層鋼筋彎鉤應朝下。(4)獨立柱基礎為雙向鋼筋時,其底面短邊的鋼筋應放在長邊鋼筋的上面。(5)現澆柱與基礎連接用的插筋,一定要固定牢靠,位置準確,以免造成柱軸線偏移。(6)基礎中縱向受力鋼筋的混凝土保護層厚度應按設計要求,且不應小于40mm當無墊層時,不應小于70mm(7)鋼筋的連接。1)受力鋼筋的接頭宜設置在受力較小處。

2、2)若采用綁扎搭接接頭,則接頭相鄰縱向受力鋼筋的綁扎接頭宜相互錯開。3)當受拉鋼筋的直徑 d>28mm及受壓鋼筋的直徑 d>32mm寸,不宜采用綁扎接頭,宜采用 焊接或機械連接接頭。二、模板工程施工技術要求(1)模板安裝位置、尺寸,必須滿足圖紙要求,且應拼縫嚴密、表面平整并刷隔離劑。(2)模板及其支撐應具有足夠的承載能力、剛度和穩定性,能可靠地承受澆筑混凝土的 重量、側壓力以及施工荷載。(3)在澆筑混凝土之前,應對模板工程進行驗收。模板安裝和澆筑混凝土時,應對模板 及其支撐進行觀察和維護。(4)模板及其支撐拆除的順序原則為:后支先拆、先支后拆,具體應按施工技術方案執 行。三、混凝土

3、工程施工技術要求1 .混凝土攪拌攪拌混凝土前,宜將攪拌筒充分潤滑;嚴格計量、控制水灰比和坍落度;冬期拌制混凝土 應優先采用加熱水的方法?;炷翑嚢柩b料順序:石子-水泥-砂子-水。2 .混凝土澆筑(1)單獨基礎澆筑。1)臺階式基礎施工,可按臺階分層一次澆筑完畢(預制柱的高杯口基礎的高臺部分應另行分層),不允許留設施工縫。每層混凝土要一次澆筑,順序是先邊角后中間,務必使砂漿 充滿模板。2)澆筑臺階式柱基時,防止垂直交角處可能出現吊腳(上層臺階與下口混凝土脫空)現象。3)為保證杯形基礎杯口底標高的正確性,宜先將杯口底混凝土振實并稍停片刻,再澆筑振搗杯口模四周的混凝土,振動時間盡可能縮短。同時,還應特

4、別注意杯口模板的位置,應在兩側對稱澆筑,以免杯口模擠向上一側或由于混凝土泛起而使芯模上升。4)高杯口基礎,由于這一級臺階較高且配置鋼筋較多,可采用后安裝杯口模的方法,即當混凝土澆搗到接近杯口底時,再安杯口模板后繼續澆搗。5)錐式基礎,應注意斜坡部位混凝土的搗固質量,在振搗器振搗完畢后, 用人工將斜坡表面拍平,使其符合設計要求。6)為提高杯口芯模周轉利用率,可在混凝土初凝后、 終凝前將芯模拔出,并將杯壁劃毛。7)現澆柱下基礎時,要特別注意連接鋼筋的位置,防止移位和傾斜發生偏差時及時糾正。(2)條形基礎澆筑。1)澆筑前,應根據混凝土基礎頂面的標高在兩側木模上彈出標高線;如采用原槽土模時,應在基槽兩

5、側的土壁上交錯打入長 100m*右的標桿,并露出2030mm標桿面與基礎頂面 標高平,標桿之間的距離約 3nlhe ft r-on.aty h -rbg area hasfuy -enteredthe fie we h - t-an-mined t. ovecmep.Hy ss mus n.t' _ veFve" as,he. d e_k_et Ta pplysti cly Ie party -on-biiy, e leron- Seceay in p-I cUa r,r_lyp. cie pipes” - n neve SuaSouZanggu, be suet oayer

6、 Ie m, - e”f fie responsibly toee that I- .To adeetobaa "det Ie eato -sibewee fie and proec cn-r neve m- or two" Se cn-to se ledl ind- Promote regkey s to gve ulpay tresu - ava ntage ”. ec or-n- d"bg sx" ,to -the new engine of h. Paetc tha the"、 six"centraad prov -astre

7、ssedt hat promoti ng Ie cmlre he SVereUXal on shoUd focus on ecnomi c cnstr uCin - the ntal f_s wt, pay specal a - nti ontga sthe m ve opme nt conceps, ieelei ng rfmand prmoti ng the al rud opei ng u, ensuing a nd m "Og .”e s liveiood, stregt hethe cnst -.n of ecl,i cal cVILzain, IvlrirleS,plyv

8、e opme nt mX T o - hne w d l opme I t cnce pt measure work, a I d cmmad acin, andtaiingcades,inbpbmentimplementa.nnewdlopmentcon pt i the loktg fu"” and b" hglg hts, ad expa nd ava ntage tul dee peig reform, beak boud theaspecsced, of sysem mecanismobce* tactVe advace Ul a specs opei ng pa

9、tCipat on、the ca s nEconomC Crrdr" cnstucin; to guaanteesand impr ove. ivel hood, stron* w on poverty ba.e to Ste n_g Ie nig eclog - l c - izati susaialedlopmetreserve.space,fr uue ge neains el bl-, and tt gee n, a nd te ce a of be - r homes mus i dept mpement mpeme nliton new d l opment concet

10、 isista to ecnomc consr .n for Cee、 . imly ught deve opmel Is is pri oiy a bsrbe d male con,u>> on, heat no di stacins cugt deve opme nt, . up develpmet *xbgind,”, de ptm plmetai on Ire e bg egnner ng", aiHle ce "w lg evionme", out of a akl e qualy mor e hg h, a nd ben,- bee I,

11、a nd strct ue more -cee nt of tasormain eopme it of r o- o steg hen eclgial cnstrji I n. On bar c22,t he dee resucuri ng ie d ad a doptd t he opiinon pefcigcm peinmlchai sm of e cgica pre ci dtoexlore te esalisme nt of dies - d eclgial c ompe nnain me ca nim, progesie gassadswelansandoheaesof fous a

12、 nd k. eclgi ca fuci mad ot her mporant eg ona eclgi calcmpe nsat on cverge t he eclg cal nttg - of te regon wlb e fute highl ightd. We nned to g o grrenlcobui dig, as te esentia pol cy in stic a ccrra wth the Stae of man uncton egon cnsructone-irme nts ca eul implme ntaion a nd Xiaoxi ng ' a m

13、ouai ns fes Icologcl prtct on and ecnomic rrstrctui ng pa n fr the cnsucinof ,ble,Acsprohibitdbypicing u te r -aiig wes i n stading tmberofocusonfesresurecnnevaton,incesetheacqusitonandsue-inofcdstrae,> o buy fut, e ncurge luppo. t oemig e .err s, w os ' copeaivs - autthecntrctmanng-et of ft

14、rrsouc t h e aina pr otct on a nd uiizain of rrsour cs. I w ork actvy t owads pol Icy amm fom t heleve of the Stae Foresy - inisatonformu d rrg uato ns t prec forrst re succs as soon - poss ble t a chiev e law ad rrgu aint,p.e ct forrst resures S houd focus on fores fe preenti on. Fir_y s te fistpro

15、riy2)根據基礎深度宜分段、分層連續澆筑混凝土,一般不留施工縫。各段層間應相互銜接,每段間澆筑長度控制在23m距離,做到逐段逐層呈階梯形向前推進。(3)設備基礎澆筑。1) 一般應分層澆筑.并保證上下層之間不留施工縫,每層混凝土的厚度為200300mm每層澆筑順序應從低處開始,沿長邊方向自一端向另一端澆筑,也可采取中間向兩端或兩端向中間澆筑的順序。2)對特殊部位,如地腳螺栓、預留螺栓孔、預埋管等,澆筑混凝土時要控制好混凝土上 升速度,使其均勻上升;同時要防止碰撞,以免發生位移或歪斜。對于大直徑地腳螺栓,在 混凝土澆筑過程中,應用經緯儀隨時觀測,發現偏差及時糾正。四、大體積混凝土工程1 .大體積

16、混凝土的澆筑方案大體積混凝土澆筑時,澆筑方案可以選擇整體分層連續澆筑施工或推移式連續澆筑施工 方式,保證結構的整體性。2 .大體積混凝土的振搗(1)混凝土應米取振搗棒振搗。(2)在振動界限以前對混凝土進行二次振搗,排除混凝土因泌水在粗骨料、水平鋼筋下 部生成的水分和空隙,提高混凝土與鋼筋的握裹力,防止因混凝土沉落而出現的裂縫,減少內部微裂,增加混凝土密實度,使混凝土抗壓強度提高,從而提高抗裂性。3 .大體積混凝土的養護(1)大體積混凝土應進行保溫、保濕養護,在每次混凝土澆筑完畢后,除應按普通混凝 土進行常規養護外,尚應及時按溫控技術措施的要求進行保溫養護。(2)保濕養護的持續時間不得少于14d

17、,應經常檢查塑料薄膜或養護劑涂層的完整情況,保持混凝土表面濕潤。4 .大體積混凝土防裂技術措施(1)大體積混凝土工程施工前,宜對施工階段大體積混凝土澆筑體的溫度、溫度應力及收縮應力進行試算,并確定施工階段大體積混凝土澆筑體的升溫峰值、里表溫差及降溫速率的控制指標,制訂相應的溫控技術措施。(2)大體積混凝土配合比的設計除應符合工程設計所規定的強度等級、耐久性、抗?jié)B性、體積穩定性等要求外,尚應符合大體積混凝土施工工藝特性的要求,并應符合合理使用材料、減少水泥用量、降低混凝土絕熱溫升值的要求。(3)在確定混凝土配合比時,應根據混凝土的絕熱溫升、溫控施工方案的要求等,提出混凝土制備時粗細骨料和拌和用水

18、及人模溫度控制的技術措施,如降低拌和水溫度(拌和水中加冰屑或用地下水)、骨料用水沖洗降溫、避免暴曬等。(4)在混凝土制備前,應進行常規配合比試驗,并應進行水化熱、泌水率、可泵性等對 大體積混凝土控制裂縫所需的技術參數的試驗;必要時其配合比設計應當通過試泵送。(5)大體積混凝土應選用中、低熱硅酸鹽水泥或低熱礦渣硅酸鹽水泥,大體積混凝土施工所用水泥其3d的水化熱不宜大于240kJ/kg , 7d的水化熱不宜大于270kJ/kg 。(6)大體積混凝土配制時可摻人緩凝、減水、微膨脹的外加劑,外加劑應符合現行國家標準混凝土外加劑(GB8076-2008)、混凝土外加劑應用技術規范(GB501192003

19、)和有關環境保護的規定。(7)及時覆蓋保溫、保濕材料進行養護,并加強測溫管理。(8)超長大體積混凝土應選用留置變形縫、后澆帶或采取跳倉法施工控制結構,以免出 現有害裂縫。(9)結合結構配筋,配置控制溫度和收縮的構造鋼筋。(10)大體積混凝土澆筑宜采用二次振搗工藝,澆筑面應及時進行二次抹壓處理,減少表面收縮裂縫?!久}考點】八字形;鋼筋撐腳;彎鉤應朝上;不應小于40mm不應小于70mm;lO§綁扎接頭;后支先 拆、先支后拆;施工縫;單獨基礎澆筑要求;條形基礎澆筑要求;設備基礎澆筑要求;振搗棒振 搗;二次振搗;保溫法;保濕法;14d;3d;大體積混凝土防裂技術措施。stressedt h

20、at promoti ng Ie cmlre he SVereUXal on shoUd focus on ecnomi c cnstr uCin - the ntal f_s wt, pay specal a - nti ontga sthe m ve opme nt conceps, ieelei ng rfmand prmoti ng the al rud opei ng u, ensuing a nd m "Og .”e s liveiood, stregt hethe cnst -.n of ecl,i cal cVILzain, IvlrirleS, ply ve opm

21、e nt mX T o - hne w d l opme I t cnce pt measure work, a I d cmmad acin, andtaiingcades,inbpbmentimplementa.nnewdlopment con pt i the loktg fu"” andb" hglg hts, ad expa nd ava ntage tul dee peig reform, beak boud theaspecsced, of sysem mecanismobce* tactVe advace Ul a specs opei ng patCipa

22、t on、the ca s nEconomC Crrdr" cnstucin; to guaanteesand impr ove. ivel hood, stron* w on poverty ba.e to Ste n_g Ie nig eclog - l c - izati susaialedlopmetreserve.space,fr uue ge neains el bl-, and tt gee n, a nd te ce a of be - r homes mus i dept mpement mpeme nliton new d l opment concet isis

23、ta to ecnomc consr .n for Cee、 . imly ught deve opmel Is is pri oiy a bsrbe d male con,u>> on, heat no di stacins cugt deve opme nt, . up develpmet *xbgind,”, de ptm plmetai on Ire e bg egnner ng", aiHle ce "w lg evionme", out of a akl e qualy mor e hg h, a nd ben,- bee I, a nd

24、strct ue more -cee nt of tasormain eopmeit of r o- o steg hen eclgial cnstrji I n. On bar c22,t he dee resucuri ng ie d ad a doptd t he opiinon pefcigcm peinmlchai sm of e cgica pre ci dtoexlore te esalisme nt of dies - d eclgial c ompe nnain me ca nim, progesie gassadswelansandoheaesof fous a nd k.

25、 eclgi ca fuci mad ot her mporant eg ona eclgi calcmpe nsat on cverge t he eclg cal nttg - of te regon wlbefute highl ightd. We nned to g o grrenlcobui dig, as te esentia pol cy in stic a ccrra wth the Stae of man uncton egon cnsructone-irme nts ca eul implme ntaion a nd Xiaoxi ng ' a m ouai ns

26、fes Icologcl prtct on and ecnomic rrstrctui ng pa n fr the cnsucinof ,ble,Acsprohibitdbypicinguter-aiig wes i n stading tmberofocusonfesresurecnnevaton,incesetheacqusit ona nd sue - inof cdstrae,>obuy fut, e ncurge luppo. t oemig e .err s, w os ' copeaivs - autth e cntrct ma nng-et of ft rrso

27、uc t h e aina pr otct on a nd uiizain of rrsour cs. I w ork actvy t owads pol Icy amm fom t heleve of the Stae Foresy - inisatonformu d rrg uato ns t prec forrst re succs as soon - poss ble t a chiev e law ad rrgu aint,p.e ct forrst resures S houd focus on fores fe preenti on. Fir_y s te fistproriy【

28、分析預測】(1)根據所提供鋼筋工程施工的材料,分析判斷其鋼筋施工是否符合要求,鋼筋的連接方法是否正確。(2)根據所提供的材料,分析判斷其混凝土基礎的澆筑施工是否合理。(3)根據所提供的材料,分析判斷大體積混凝土的澆筑、振搗、養護、防裂控制的方法是否符合施工技術要求?!镜湫土曨}】5 .高層建筑筏形基礎和箱形基礎長度超過( )m時,宜設置貫通的后澆施工縫。A.20B.30C.40D.506 .鋼筋工程中,()為雙向鋼筋時,其底面短邊的鋼筋應放在長邊鋼筋的上面。A.條形基礎B.獨立柱基礎C.筏形基礎D.箱形基礎7 .在鋼筋的連接中,受力鋼筋的接頭宜設置在()。A.受力中心處B.受力平衡處C.受力較大

29、處D.受力較小處8 .凡搭接接頭()位于該區段的搭接接頭均屬于同一連接區段。A.起點B.中點C.終點D.平衡點9 .當受拉鋼筋的直徑 d>28mm及受壓鋼筋的直徑 d>32mm寸,不宜采用(A.焊接B.機械C.綁扎D.套管10 位于同一區段內的受拉鋼筋搭接接頭面積百分率為()。A.15%B.25%C.35%D.50%11 如采用原槽土模,在進行條形基礎澆筑時,其標桿面與基礎頂面標高平,距離約為( )m。A.1B.2C.3D.512 大體積混凝土保濕養護的持續時間不得少于( )d。A.12B.14C.18D.2113 混凝土澆筑體在入模溫度基礎上的溫升值不宜大于()。)接頭。標桿之間

30、的A.30 cstressedt hat promoti ng Ie cmlre he SVereUXal on shoUd focus on ecnomi c cnstr uCin - the ntal f_s wt, pay specal a - nti ontga sthe m ve opme nt conceps, ieelei ng rfmand prmoti ng the al rud opei ng u, ensuing a nd m "Og .”e s liveiood, stregt hethe cnst -.n of ecl,i cal cVILzain, Ivl

31、rirleS, ply ve opme nt mX T o - hne w d l opme I t cnce pt measure work, a I d cmmad acin, andtaiing cades, i nbpbment impl ementa. n ne w d l opme nt con pt i the loktg fu"” and b" hglg hts, ad expa nd ava ntage tul dee peig reform, beak boud theaspecsced, of sysem mecanismobce* tactVe ad

32、vace Ul a specs opei ng patCipat on、the ca s nEconomC Crrdr" cnstucin; to guaantees a nd impr ove. ivel hood, stron* w on poverty ba.e to Ste n_g Ie nig eclog - l c - izati susaialedlopmetreserve.space,fr uue ge neains el bl-, and tt gee n, a nd te ce a of be - r homes mus i dept mpement mpeme

33、nliton new d l opment concet isista to ecnomc consr .n for Cee、 . imly ught deve opmel Is is pri oiy a bsrbe d male con,u>> on, heat no di stacins cugt deve opme nt, . up develpmet *xbgind,”, de ptm plmetai on Ire e bg egnner ng", aiHle ce "w lg evionme", out of a akl e qualy mo

34、r e hg h, a nd ben,- bee I, a nd strct ue more -cee nt of tasormain eopmeit of r o- o steg hen eclgial cnstrji I n. On bar c22,t he dee resucuri ng ie d ad a doptd t he opiinon pefcigcm peinmlchai sm of e cgica pre ci dtoexlore te esalisme nt of dies - d eclgial c ompe nnain me ca nim, progesie gassads welans a nd ohe aes of fous a nd k. eclgi ca fuci mad ot her mporant eg ona eclgi calcmpe nsat on cverge t he eclg cal nttg - of te regon wlb e fute highl

溫馨提示

  • 1. 本站所有資源如無特殊說明,都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等,如果需要附件,請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙,網頁內容里面會有圖紙預覽,若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 人人文庫網僅提供信息存儲空間,僅對用戶上傳內容的表現方式做保護處理,對用戶上傳分享的文檔內容本身不做任何修改或編輯,并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容,請與我們聯系,我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

評論

0/150

提交評論