噴漆過程關鍵序控制KeySequencetoControlthePaintingProcess客戶；性能要求（噴漆)Customers;performancerequirements(painting)1/膜厚;≥40um（膜厚儀）

1/thickness;≥40um(thicknessanalyzer)2/附著力；GT1-GTO（1mm劃格儀）2/adhesiveforce;GT1-GTO(1mmHatchInstrument)3/光澤；1.1-1.5（60℃、光澤儀）3/Lustre;1.1-1.5(60℃、Glossmeter)

4/色差；1DH:d1:(0.6--0.4)4/Colordifference;1DH:d1:(0.6--o.4)da:(0.15--0.45)db(0.45--0.15)噴漆過程關鍵程序控制。Tomeetcustomersperformancerequirements,thekeysequencecontrolofthepaintingprocess

為滿足客戶性能要求油漆攪拌:首次原漆攪拌30分鐘二次3-5分鐘（汽動攪拌器）

Paintmixing:forthefirsttimetheoriginalpaintstirring30minutes,thesecond3-5minutes(Pneumaticagitator)油漆過濾:200目尼龍網PaintFilter:200meshnylonnet

油漆活化時間:調配后油漆使用不大于60分鐘，容器外貼起始時間單paintactivationtime:painttousewithin60minutes,markstarttimeontheoutsiceofthecontainer

油漆放置:密封儲存，再次使用確認狀態

Paintplacement:sealedandstored,useagaintoconfirmstatus

油漆粘度:巖田2#杯20-25秒paintviscosity:Iwata＃2cupsof20-25seconds注意事項:調漆前保質期、包裝完好確認Attention:paintbeforetheshelflife,packagingintactrecognized

調漆工序PaintMixingProcesses調漆工序工作中的安全防護

Securitymeasuresinthepaintprocess

有害成分:有機溶劑、合成樹脂HarmfulIngredients:organicsolvents,syntheticresin存在的損害:呼吸、皮膚、PossibleDamage:respiratorysystem,skin,預防和保護:防有機氣體口罩（3M)抗溶劑手套抗靜電服、帽子Preventionandprotection:Anti-organicmasks(3m),anti-solventgloves,anti-staticclothingandcaps基本保護：專用調漆室，排風良好Basicprotection:Dedicatedpaintingroomswithgoodventilation噴漆工序PaintingProcess

風速:

0.3-0.6m/min(風速儀，飄帶）Windspeed:0.3-0.6/min(Anemometers,ribbon)

溫度:18-28度Temperature:18-28℃

人員著裝:噴漆保護，服裝Staffdress:paintprotectionclothing噴漆標準作業:噴漆標準作業分解Paintstandardoperating:paintstandardoperatingdecompotion膜厚控制:每批6點膜厚片（上中下）中央通道

Filmthicknesscontrol:eachbatchof6:00thickness-chip噴漆工序工作中的安全防護

Securitymeasuresintheworkofpaintingprocess有害成分:漆霧中可能含有鉛、鋅等重金屬、有機溶劑、合成樹脂Harmfulingredients:maycontainlead,zincandotherheavymetals,organicssolvents,syntheticresininthemist

存在的損害:呼吸、皮膚、Exsistenceofdamage:respiratory.skin預防和保護:防有機氣體口罩（3M)抗溶劑手套抗靜電服、帽子Preventionandprotection:Anti-organicmasks(3m),anti-solventgloves,anti-staticclothingandcaps

烘干工序Dryingprocesses鏈速:0.6-0.9m/min（XX產品鏈速為0.7m/min,烘烤時間40分鐘)Chainspeed:0.6-0.9m/minXXchainspeed0.7m/min,bakingtime40min)烘烤時間:45-30分鐘Bakingtime:30-45min烘烤溫度:78±2℃Bakingtemperature:78±2℃

噴漆過程參數監控:每兩小時一次Paintingprocessprametermonitoring:onceeverytwohours噴漆產品檢驗實測值

SprayProductsTestingMeasuredValues膜厚：58umFilmthickness:58UM附著力：GT1Adhesiveforce:GT1

光澤：1DH1.3Luster:1DH1.3色差值：d1:0.5da:-0.26db:0.18ValueofChromatism:d1:0.5da:-0.26db:0.18參數值對比在范