概要與操概此范例程序?qū)⒔榻B如何透過定時器對象在預設時間去觸發特定位.以下介紹定設敘定時器主開關預設時間設定計時時間數值已計時間定時器目前已計數值定時器對象包含五種模式ON],OFF脈沖啟動開關累ON]及[OFF].以下將一一介紹每個模式:操[PT后,觸碰IN去觸發定時器開始倒數同時TI被設ON)倒數結束之后,TIOFF同時Q[PT后,IN準備定時器倒數.(同時QIN,倒數完成后,TI及Q[脈沖啟動開關PT后,觸碰IN去觸發定時器倒數TI及Q被ON)倒數結束后,TI及Q[PT后,觸碰IN去觸發定時器倒數.(同時TI倒數結束后,TIOFF,Q被設為注記:如要再次操作此模式前,使用者必須觸發RET[PT后,觸碰IN準備定時器倒數.(同時Q當使用者再次觸碰IN時.倒數結束后,TI及Q注記:如要再次操作此模式前,使用者必須觸發RET窗口設[延時開關點選定時器對象并選擇延時開關ON及時間單位后,設定所需的相關地址.在此范例程序中IN設為L(zhǎng)B0,TI為L(zhǎng)B1,Q為L(zhǎng)B2,PT為L(zhǎng)W0,ET為L(zhǎng)W1.IN,TI及Q.然后建立數值輸入對象為數值顯示對象為[延時開關OFF],[脈沖啟動開關11為延時開關OFF12為脈沖啟動開關所有所需對象及設定皆與延時開關ON相同,請參考延時開關ON相關設定[累加式延時開關ON],[累加式延時開關點選定時器物件并設累加式延時開關ON/累加式延時開關OFF和時間單位后,設定所須對象地址,在此模式中我們?cè)O(shè)IN為L(zhǎng)B0,TI為L(zhǎng)B1,Q為L(zhǎng)B2,PT為L(zhǎng)W0,ET為L(zhǎng)W1,R為L(zhǎng)B3.IN,TI,QR.PT,和數值顯示對象為地此范例程序所使用到的對