計算機網絡實驗四：路由器的配置_第1頁
計算機網絡實驗四：路由器的配置_第2頁
計算機網絡實驗四：路由器的配置_第3頁
計算機網絡實驗四：路由器的配置_第4頁
計算機網絡實驗四：路由器的配置_第5頁
已閱讀5頁，還剩5頁未讀， 繼續免費閱讀

下載本文檔

版權說明：本文檔由用戶提供并上傳，收益歸屬內容提供方，若內容存在侵權，請進行舉報或認領

文檔簡介

1、天津理工大學實驗報告學院（系）名稱：計算機與通信工程學院姓名學號專業計算機科學與技術（中加）班級教學2班實驗項目實驗四：路由器的配置課程名稱計算機網絡課程代碼0662016實驗時間2015年6月25日 第7、8節實驗地點7-219批改意見成績教師簽字： （一） 實驗?zāi)康模?掌握利用超級終端配置路由器時的連接和參數設置；掌握路由器的常見模式及其轉換命令；掌握用配置向?qū)渲寐酚善鞯牟襟E和方法；掌握檢查路由器配置和狀態的路由器命令。掌握路由器配置文件管理方法，掌握靜態路由和動態路由的配置方法。（二）實驗環境：軟件環境：Windows 2000XP 硬件環境：IBMPC或兼容機局域網、PC機連入Int

2、ernet（三）實驗學時：2學時，必做.（四）實驗要求：利用超級終端進行路由器的配置，記錄配置過程，在實驗報告中注明各種命令的功能。進行網絡地址規劃，配置路由器；檢查路由器配置。掌握路由協議的種類和特點。掌握靜態路由、默認路由的配置方法。掌握查看路由條目的方法，并驗證路由的作用。（6） 實驗步驟： 1.設計并連接網絡。2.連接主機與路由器。3.配置各個接口。 4.最后配置路由表。配置RIP：#rip 1 version 2 network 0.0.0.0#路由表：r1display ip routing-tableRouting Tables: Public Destinations : 10

3、 Routes : 10Destination/Mask Proto Pre Cost NextHop Interface20.0.1.0/24 Direct 0 0 20.0.1.1 Eth0/020.0.1.1/32 Direct 0 0 127.0.0.1 InLoop020.0.2.0/24 Direct 0 0 20.0.2.1 S2/020.0.2.1/32 Direct 0 0 127.0.0.1 InLoop020.0.2.2/32 Direct 0 0 20.0.2.2 S2/020.0.3.0/24 RIP 100 1 20.0.2.2 S2/020.0.4.0/24 RI

4、P 100 1 20.0.2.2 S2/020.0.5.0/24 RIP 100 2 20.0.2.2 S2/0127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0接口信息：r1display ip int b*down: administratively down(s): spoofingInterface Physical Protocol IP Address DescriptionAux0 down down unassigned Aux0 Inte.Cellular0/0 d

5、own down unassigned Cellular0.Eth0/0 up up 20.0.1.1 Ethernet0.Eth0/1 down down unassigned Ethernet0.S1/0 down down unassigned Serial1/0.S2/0 up up 20.0.2.1 Serial2/0.測試連通性：C:Documents and Settingsstudping 20.0.5.2Pinging 20.0.5.2 with 32 bytes of data:Reply from 20.0.5.2: bytes=32 time=36ms TTL=253R

6、eply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Ping statistics for 20.0.5.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),Approximate round trip times in milli-seconds:Minimum = 36ms, Maximum = 36ms,

7、Average = 36ms配置 IP:#interface Ethernet0/0 port link-mode route ip address 20.0.1.1 255.255.255.0#interface Ethernet0/1 port link-mode route#interface Serial1/0 link-protocol ppp#interface Serial2/0 link-protocol ppp ip address 20.0.2.1 255.255.255.0#配置 OSPF:#ospf 1 area 0.0.0.0 network 0.0.0.0 255.

8、255.255.255#路由表：r1display ip routing-tableRouting Tables: Public Destinations : 10 Routes : 10Destination/Mask Proto Pre Cost NextHop Interface20.0.1.0/24 Direct 0 0 20.0.1.1 Eth0/020.0.1.1/32 Direct 0 0 127.0.0.1 InLoop020.0.2.0/24 Direct 0 0 20.0.2.1 S2/020.0.2.1/32 Direct 0 0 127.0.0.1 InLoop020.

9、0.2.2/32 Direct 0 0 20.0.2.2 S2/020.0.3.0/24 OSPF 10 1572 20.0.2.2 S2/020.0.4.0/24 OSPF 10 3124 20.0.2.2 S2/020.0.5.0/24 OSPF 10 3125 20.0.2.2 S2/0127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0接口信息：r1display ip int b*down: administratively down(s): spoofingInterfac

10、e Physical Protocol IP Address DescriptionAux0 down down unassigned Aux0 Inte.Cellular0/0 down down unassigned Cellular0.Eth0/0 up up 20.0.1.1 Ethernet0.Eth0/1 down down unassigned Ethernet0.S1/0 down down unassigned Serial1/0.S2/0 up up 20.0.2.1 Serial2/0.測試連通性：C:Documents and Settingsstudping 20.0

11、.5.2Pinging 20.0.5.2 with 32 bytes of data:Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Ping statistics for 20.0.5.2: Packets: Sent = 4, Received = 4, Lost =

12、 0 (0% loss),Approximate round trip times in milli-seconds:Minimum = 36ms, Maximum = 36ms, Average = 36ms配置靜態路由：R1ip routR1ip route-static 20.0.3.0 255.255.255.0 20.0.2.2R1ip routR1ip route-static 20.0.4.0 255.255.255.0 20.0.2.2R1ip routR1ip route-static 20.0.5.0 255.255.255 .0 20.0.2.2測試連通性：R1ping

13、20.0.5.2 PING 20.0.1.1: 56 data bytes, press CTRL_C to break Reply from 20.0.1.1: bytes=56 Sequence=1 ttl=255 time=25 ms Reply from 20.0.1.1: bytes=56 Sequence=2 ttl=255 time=24 ms Reply from 20.0.1.1: bytes=56 Sequence=3 ttl=255 time=25 ms Reply from 20.0.1.1: bytes=56 Sequence=4 ttl=255 time=25 ms

14、 Reply from 20.0.1.1: bytes=56 Sequence=5 ttl=255 time=24 ms - 20.0.1.1 ping statistics - 5 packet(s) transmitted 5 packet(s) received0.00% packet lossround-trip min/avg/max = 24/24/25 msR2：配置RIP：#rip 1 version 2 network 0.0.0.0#路由表：H3C-rip-1display ip routing-tableRouting Tables: Public Destination

15、s : 12 Routes : 12Destination/Mask Proto Pre Cost NextHop Interface20.0.1.0/24 RIP 100 1 20.0.2.1 S2/020.0.2.0/24 Direct 0 0 20.0.2.2 S2/020.0.2.1/32 Direct 0 0 20.0.2.1 S2/020.0.2.2/32 Direct 0 0 127.0.0.1 InLoop020.0.3.0/24 Direct 0 0 20.0.3.1 Eth0/020.0.3.1/32 Direct 0 0 127.0.0.1 InLoop020.0.4.0

16、/24 Direct 0 0 20.0.4.1 S1/020.0.4.1/32 Direct 0 0 127.0.0.1 InLoop020.0.4.2/32 Direct 0 0 20.0.4.2 S1/020.0.5.0/24 RIP 100 1 20.0.4.2 S1/0127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0接口信息：H3C-rip-1display ip int b*down: administratively down(s): spoofingInterface

17、 Physical Protocol IP Address DescriptionAux0 down down unassigned Aux0 Inte.Cellular0/0 down down unassigned Cellular0.Eth0/0 up up 20.0.3.1 Ethernet0.Eth0/1 down down unassigned Ethernet0.S1/0 up up 20.0.4.1 Serial1/0.S2/0 up up 20.0.2.2 Serial2/0.測試連通性：C:Documents and Settingsstudping 20.0.5.2Pin

18、ging 20.0.5.2 with 32 bytes of data:Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Ping statistics for 20.0.5.2: Packets: Sent = 4, Received = 4, Lost = 0 (0%

19、loss),Approximate round trip times in milli-seconds:Minimum = 36ms, Maximum = 36ms, Average = 36ms配置IP：#interface Ethernet0/0 port link-mode route ip address 20.0.3.1 255.255.255.0#interface Ethernet0/1 port link-mode route#interface Serial1/0 link-protocol ppp ip address 20.0.4.1 255.255.255.0#inte

20、rface Serial2/0 link-protocol ppp ip address 20.0.2.2 255.255.255.0#配置OSPF:#ospf 1 area 0.0.0.0 network 0.0.0.0 255.255.255.255#路由表：H3Cdisplay ip routing-tableRouting Tables: Public Destinations : 12 Routes : 12Destination/Mask Proto Pre Cost NextHop Interface20.0.1.0/24 OSPF 10 1563 20.0.2.1 S2/020

21、.0.2.0/24 Direct 0 0 20.0.2.2 S2/020.0.2.1/32 Direct 0 0 20.0.2.1 S2/020.0.2.2/32 Direct 0 0 127.0.0.1 InLoop020.0.3.0/24 Direct 0 0 20.0.3.1 Eth0/020.0.4.0/24 Direct 0 0 20.0.4.1 S1/020.0.4.1/32 Direct 0 0 127.0.0.1 InLoop020.0.4.2/32 Direct 0 0 20.0.4.2 S1/020.0.5.0/24 OSPF 10 1563 20.0.4.2 S1/012

22、7.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0接口信息：H3Cdisplay ip int b*down: administratively down(s): spoofingInterface Physical Protocol IP Address DescriptionAux0 down down unassigned Aux0 Inte.Cellular0/0 down down unassigned Cellular0.Eth0/0 up up 20.0.3.1 Ether

23、net0.Eth0/1 down down unassigned Ethernet0.S1/0 up up 20.0.4.1 Serial1/0.S2/0 up up 20.0.2.2 Serial2/0.測試連通性：C:Documents and Settingsstudping 20.0.5.2Pinging 20.0.5.2 with 32 bytes of data:Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Reply from 20.0.5

24、.2: bytes=32 time=36ms TTL=253Reply from 20.0.5.2: bytes=32 time=36ms TTL=253Ping statistics for 20.0.5.2: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss),Approximate round trip times in milli-seconds:Minimum = 36ms, Maximum = 36ms, Average = 36ms配置靜態路由：R2ip routR2ip route-static 20.0.1.0 255.25

25、5.255.0 20.0.2.2R2ip routR2ip route-static 20.0.5.0 255.255.255 .0 20.0.2.2測試連通性：R2ping 20.0.5.2 PING 20.0.5.2: 56 data bytes, press CTRL_C to breakReply from 20.0.5.2: bytes=56 Sequence=1 ttl=127 time=25 ms Reply from 20.0.5.2: bytes=56 Sequence=2 ttl=127 time=25 ms Reply from 20.0.5.2: bytes=56 Se

26、quence=3 ttl=127 time=24 ms Reply from 20.0.5.2: bytes=56 Sequence=4 ttl=127 time=25 ms Reply from 20.0.5.2: bytes=56 Sequence=5 ttl=127 time=25 ms - 20.0.5.2 ping statistics - 5 packet(s) transmitted 5 packet(s) received 0.00% packet lossround-trip min/avg/max = 24/24/25 msR3：配置RIP：#rip 1 version 2

27、 network 0.0.0.0#路由表：H3Cdisplay ip routing-tableRouting Tables: PublicDestinations : 10 Routes : 10Destination/Mask Proto Pre Cost NextHop Interface20.0.1.0/24 OSPF 10 3125 20.0.4.1 S1/020.0.2.0/24 OSPF 10 3124 20.0.4.1 S1/020.0.3.0/24 OSPF 10 1572 20.0.4.1 S1/020.0.4.0/24 Direct 0 0 20.0.4.2 S1/020

28、.0.4.1/32 Direct 0 0 20.0.4.1 S1/020.0.4.2/32 Direct 0 0 127.0.0.1 InLoop020.0.5.0/24 Direct 0 0 20.0.5.1 Eth0/020.0.5.1/32 Direct 0 0 127.0.0.1 InLoop0127.0.0.0/8 Direct 0 0 127.0.0.1 InLoop0127.0.0.1/32 Direct 0 0 127.0.0.1 InLoop0接口信息：H3Cdisplay ip int b*down: administratively down(s): spoofingIn

29、terface Physical Protocol IP Address DescriptionAux0 down down unassigned Aux0 Inte.Cellular0/0 down down unassigned Cellular0.Eth0/0 up up 20.0.5.1 Ethernet0.Eth0/1 down down 10.0.0.9 Ethernet0.S1/0 up up 20.0.4.2 Serial1/0.S2/0 down down 2.0.0.1 Serial2/0.測試連通性：C:Documents and Settingsstudping 20.

30、0.3.2Pinging 20.0.3.2 with 32 bytes of data:Reply from 20.0.3.2: bytes=32 time=36ms TTL=253Reply from 20.0.3.2: bytes=32 time=36ms TTL=253Reply from 20.0.3.2: bytes=32 time=36ms TTL=253Reply from 20.0.3.2: bytes=32 time=36ms TTL=253Ping statistics for 20.0.3.2: Packets: Sent = 4, Received = 4, Lost

31、= 0 (0% loss),Approximate round trip times in milli-seconds:Minimum = 36ms, Maximum = 36ms, Average = 36ms配置 IP:#interface Ethernet0/0 port link-mode route ip address 20.0.5.1 255.255.255.0#interface Ethernet0/1 port link-mode route#interface Serial1/0 link-protocol ppp ip address 20.0.4.2 255.255.2

32、55.0#interface Serial2/0 link-protocol ppp#配置 OSPF:ospf 1 area 0.0.0.0 network 0.0.0.0 255.255.255.255#路由表：r3display ip routing-tableRouting Tables: Public Destinations : 10 Routes : 10Destination/Mask Proto Pre Cost NextHop Interface20.0.1.0/24 OSPF 10 1572 20.0.1.1 S2/020.0.1.1/32 Direct 0 0 127.0.0.1 InLoop020.0.2.0/24 OSPF 10 3124 20.0.2.1 S2/020.0.2.1/32 Direct 0 0 127.0.0.1 InLoop020.0.2.2/32 Direct 0 0 20.0.2.2 S2/020.0.3.0/24 OSPF 10 3125 20.0.2.2 S2/020.0.4.0/24 Direct 0

溫馨提示

  • 1. 本站所有資源如無特殊說明，都需要本地電腦安裝OFFICE2007和PDF閱讀器。圖紙軟件為CAD,CAXA,PROE,UG,SolidWorks等.壓縮文件請下載最新的WinRAR軟件解壓。
  • 2. 本站的文檔不包含任何第三方提供的附件圖紙等，如果需要附件，請聯系上傳者。文件的所有權益歸上傳用戶所有。
  • 3. 本站RAR壓縮包中若帶圖紙，網頁內容里面會有圖紙預覽，若沒有圖紙預覽就沒有圖紙。
  • 4. 未經權益所有人同意不得將文件中的內容挪作商業或盈利用途。
  • 5. 人人文庫網僅提供信息存儲空間，僅對用戶上傳內容的表現方式做保護處理，對用戶上傳分享的文檔內容本身不做任何修改或編輯，并不能對任何下載內容負責。
  • 6. 下載文件中如有侵權或不適當內容，請與我們聯系，我們立即糾正。
  • 7. 本站不保證下載資源的準確性、安全性和完整性, 同時也不承擔用戶因使用這些下載資源對自己和他人造成任何形式的傷害或損失。

評論

0/150

提交評論