1、 液氮容器控制系統產品使用說明書成都盛杰低溫設備有限公司本說明書重點介紹了智能液氮生物容器控制系統的功能、使用方法和注意事項，我們力求使產品的信息做到最新、最準確；希望本說明書能滿足你對該產品的了解；如有疑問或需要了解進一步的產品信息，請與我們及時取得聯系。注意：用戶必須認識和了解液氮溫控和凍存樣品的復雜性。本設備是一種有用的工具，但與這種類型的所有其他設備一樣，存在固有的局限性，對于這點，用戶必須掌握。對于使用本設備不當或者未按我公司提供的方法進行操作而造成的直接或非直接的經濟損失或人員傷害，本公司拒絕承擔一切責任或義務。 目 錄 一、儀器安裝使用（一）硬件設備連接說明（二）控制系統硬件功能

2、說明（三）監控終端系統操作說明二、安全操作注意事項及常見故障三、售后服務四、特別說明（一）安全特別說明（二）功能特別說明（三）知識產權聲明五、傳感器校準一、儀器安裝使用（一）硬件設備連接與運行1、低溫管道與液氮生物容器的連接將液氮輸送管與液氮生物容器相連，液氮容器輸入壓力不應超過0.5MPa。 2、連接電源線在儀器上設有電源輸入及控制輸入輸出的專用航空接插件。用戶的電源線選用不小于2.5mm平方銅芯線。接地保護線選用2.5mm平方銅芯線與地可靠連接。如果用戶不設置保護接地線（僅有觸保器實現漏電保護），則用戶必須按電力系統規范要求，為本設備專門設置保護接地裝置與本殼體聯接。在雷電多發地區，必須有

3、防雷保護措施。如此，可以起到防止雷電對微機元器件可能造成的破壞。注意：請將本機與大地可靠連接，防止觸電事故的發生！3、試機首次使用（或長時間沒用）先將控制系統電源打開，進入系統設置菜單，在設備測試欄，手動開啟電磁閥，用干燥氮氣將系統管道中的雜質吹出（大約3分鐘），以免堵塞電磁閥而影響正常運行，重復幾次效果最佳，先注入少量液氮，待罐體內部完全冷卻后再將系統調到自動模式，設置好傳感器位置，加液停止后24小時再放入凍存物品。注意：手動開啟電磁閥試驗完畢后要記住手動關閉。4、運行根據凍品需要的溫度決定放入凍品的時間，關閉罐蓋，打開電源，選擇運行模式，設備開始工作，控制系統進入監控狀態，系統實時顯示液氮

4、罐內的溫度變化。 （二）控制系統硬件功能說明監控模塊部分：1、實時監測低位、高位溫度值。2、運行時間顯示并能根據用戶設定時間起停電磁閥。3、路控制輸出驅動電磁閥，其中2路做為備用，在另2路輸出無效時自動切換。備用輸出端作IO量檢測。4、2段程序任意選擇：浸泡式凍存、汽相式凍存。5、采用內部局域網方式罐體計算機和監控主計算機連接。報警模塊部分：1、預留1個串口，如用戶需要時可單獨配備DTU發送報警信息。2、低位、高位溫度超溫報警3、傳感器失效報警4、控制電磁閥的繼電器強電輸出端無輸出報警（三）監控終端系統操作說明本系統控制軟件由運行模式選擇、監控、報警、報警查詢、物品信息查詢、物品信息管理、手動

5、操作七個模塊組成，下面分別給以詳細說明。1、 選擇運行模式系統開機后，會根據用戶的選擇進入相應的運行模式。選擇需要的運行模式，點擊確定后重啟系統進入對應的運行模式。 2、監控模塊監控模塊實時監控杜瓦室內的溫度數據、系統運行的時間、系統運行的各種狀態等重要數據。2.1 液氮液位值顯示當前液氮的高度，單位為毫米（mm）。2.2 低位溫度顯示當前低位傳感器的溫度，單位為攝氏度（）。2.3 高位溫度顯示當前高位傳感器的溫度，單位為攝氏度（）。2.4 運行狀態顯示系統運行時的各個部件的工作狀態。（注：綠色表示正常，紅色表示異常）下圖表示低位傳感器和液位傳感器異常。用戶在此可手動對電磁閥進行打開和關閉的操

6、作，方便檢修和測試系統的輔助設備。2.4.1 低位傳感器顯示低位傳感器狀態。2.4.2 高位傳感器顯示高位傳感器狀態。2.4.3 液位傳感器顯示液位傳感器狀態。2.4.4 電池電壓顯示電池狀態。2.4.5 電磁閥輸出顯示電磁閥狀態，紅色表示電磁閥開啟。2.4.6 網絡狀態顯示網絡連接狀態，紅色表示與監控中心計算機失去連接。2.4.7 開蓋狀態顯示開蓋狀態，紅色表示開蓋。2.4.8 繼電器狀態顯示繼電器狀態。2.4.9 電源狀態顯示電源狀態。2.4.10 基本工作狀態 運行模式顯示當前程序運行的模式，運行時間顯示程序上電后運行的總時間（不可清除），開蓋次數顯示液氮罐打開蓋子的次數（不可清除）。3

7、、報警信息查看設備運行期間的所有報警記錄。4、物品信息查看液氮罐中存儲的物品的詳細信息?？筛鶕?jù)存儲物品的任意信息來搜索查看該物品的詳細情況。5、物品管理管理存儲罐中的物品，進行入庫出庫操作。5.1 入庫操作條碼槍掃描物品的條碼后，系統自動從監控中心計算機獲取物品的信息，操作員查看信息無誤后確認，物品存入液氮罐。5.2 出庫操作條碼槍掃描物品的條碼后，系統自動從數據庫獲取物品的信息，操作員查看信息無誤后確認，將物品從液氮罐中取出。6、系統設置7、溫度曲線8、主動報警系統在運行過程中出現異常，監控終端和監控中心計算機均會彈出下圖所示的報警窗口，同時發出報警聲音，提示值班人員。二、安全操作注意事項及

8、常見故障1容器屬高真空產品，運輸、安裝、使用時應小心謹慎，避免碰撞。2初次充裝液氮時，應先充入少量液氮（約100L）預冷，接近熱平衡后（氣化不劇烈），再充注液氮。3皮膚接觸到液氮，會造成凍傷，操作時應注意以下幾點：（1）一定要戴上皮手套，不可露出手腳；（2）不可穿長統鞋，避免液氮掉進鞋內；（3）不能赤手接觸旋轉柄、頸口等低溫部位，轉動旋轉柄時最好使用其他工具撥動；（4）充裝液氮時宜在通風良好的地方進行，若在室內進行，則應開啟門窗，以免發生因缺氧而造成的窒息事故。4容器的真空封口塞為活連接，可以在容器遭受意外破壞，液氮進入夾層空間，急劇汽化增壓時，將封口塞沖開，形成泄壓口，排放出氮氣，起到爆破片

9、的作用，可確保產品使用的安全可靠。嚴禁取下真空封口罩和對真空封口接頭進行任何操作，如發現該接口處有任何人為的開啟和操作痕跡，由此造成的一切損失，本公司概不負責。5運輸時應將容器放置于靠前車廂板位置，用粗繩固定牢固，不可碰撞與擦傷容器，嚴禁在滿載液氮和冷凍物品的情況下車運輸。6容器底部裝有4只高強度腳輪，可在內裝液氮和冷凍物品的情況下，方便地在室內做短距離移動，室內移動時應小心謹慎，切不可猛推猛移，防止碰撞。嚴禁在室外凹凸不平的地面移動。7不允許在產品表面施焊。常見故障及處理方法：序號故障現象故障原因處理方法1無法開啟電源保險絲燒毀更換同型號的保險絲2溫度顯示不正常溫度傳感器損壞更換溫度傳感器3

10、機器開啟但不制冷制冷劑工作壓力太低調整液氮容器輸出壓力、調至約0.2MPa4制冷電磁閥不能關閉雜質堵塞干燥氮氣吹除三、售后服務1、我公司生產的SJ系列產品保修期均為一年。用戶必須嚴格按照“產品使用說明書”規定進行正確使用和維護保養。在保修期內，用戶在正常使用條件下，發現本產品有質量問題，或使用中發生故障，由本廠負責免費修理或更換全新部件；保修期過后，本廠仍負責修理，僅收取配件費和相應的交通費。2、我公司有嚴格的售后服務制度。接到維修通知后，30分鐘內作出反應，3天內到達現場。每周星期一上午為我公司定期電話回訪時間，直接與使用人聯系，了解設備運行狀況，并做好售后服務記錄。3、我公司對系統軟件提供

11、終身升級服務。每年對設備進行一次年檢并出具年檢報告，軟件升級只收取成本價。4、免費對業主培訓1-3名技術人員。5、我公司開通24小時售后服務熱線電話：028827241076、以下情況不屬于免費保修范圍： （1）用戶擅自解剖、拆卸設備的； （2）因不可抗拒因素造成損壞的，如：災害（地震/火災/水災/雷擊等）、電壓異常等所造成的故障； （3）涂改發票或保修卡的；（注：保修期自開發票之日起算，請妥善保存保修卡和購貨發票。） （4）因用戶在運輸、裝卸、管理等過程中不當而損壞的； （5）未按使用說明書使用要求而造成損壞的。四、特別說明（一）安全特別說明1、使用液氮生物容器時必須有專人值守以確保使用的安

12、全！2、使用液氮生物容器時必須打開門窗，使空氣對流，確保通風良好，揮發的液氮可能導致小范圍缺氧，造成輕微窒息而影響人身安全！3、和液氮生物容器連接的管路必須牢固，杜絕液氮跑、冒、漏、滴、濺等現象的發生以確保操作者的安全！4、液氮生物容器停止使用后，必須將進液閥門關閉并切斷電源！5、必須使用安全合格的帶接地的三孔電源插座，確保接地正確、可靠，以保證人身安全！6、液氮生物容器使用環境必須遠離熱源、易燃品、易腐蝕性氣體、強磁場、粉塵和油污嚴重的場所！7、從液氮生物容器內取出凍品時一定要戴手套，防止凍傷的發生?。ǘ┕δ芴貏e說明1、關于罐體內部溫度的問題。由于被處理凍品的復雜多樣性以及使用環境的不確定

13、性，導致罐內溫度數據和實際的有一定誤差，僅作參考。2、關于液氮消耗量、剩余容量的問題。由于機器所處的溫度環境、液氮容器的內部壓力等因素的影響，液氮平均消耗量、液氮剩余容量數據和實際的有一定誤差，僅作參考。3、關于報警的說明?？刂葡到y(tǒng)正常工作，綠燈常亮；黃燈閃爍表示有故障；4、關于配備UPS的說明。用戶應配備在線式長延時UPS，保證在停電時設備能正常工作。若因停電而導致處理程序不能正常完成從而造成用戶的直接或間接的經濟損失，我公司不承擔任何責任！（三）知識產權聲明SJ系列不銹鋼液氮生物容器是我公司自主研發生產的國家專利產品（專利號：ZL20072008194B.X），知識產權受法律保護。任何人、

14、任何單位不得以任何形式對機器的軟硬件進行修改、改造、復制、發行或反編譯！否則我公司將依法追究相關人員的責任！五、傳感器校準（一） 在校準之前，先在測試界面把傳感器里的20個溫度值是否正常：首先，在校準值為0的情況下它們的值都大于-200度時為正常范圍其次，觀察是否離液氮越高的傳感器的值是否越大 是為正常、然后，看最下面的傳感器是否在-196度附近（有液氮的情況下）（二）在確定液位傳感器里的20只溫度傳感器沒問題的情況下： 選擇一個溫度傳感器觀察它的溫度變化是否在正負1度范圍內（三）對溫度傳感器進行每個校準：（須有2到3只溫度傳感器泡到液氮里）把泡在液氮中的傳感器的值校道跳動的中間值為-196，

15、如：傳感器0的溫度在-196.5到-197.8度范圍內跳動 ，就得把校準值設為正的11（即正1.1度）這時溫度的跳動范圍應在-195.4到-196.7度 按此方法校準另外泡在液氮里的傳感器，然后取這幾個泡在液氮里傳感器的校準值的平均值設到另外的傳感器校準值上。 Liquid nitrogen container control systemManualChengdu Shengjie Cryogenic Equipment Co., Ltd.This manual focuses on the function and use of liquid nitrogen biological con

16、tainers precautions intelligent control system, we strive to make the product information to do the latest and most accurate; hope to meet you understand the instructions for the product; case of doubt or the need for further product information, please get in touch with us.Note:The user must know a

17、nd understand the complexities and frozen in liquid nitrogen temperature control samples.This device is a useful tool, but with all other devices of this type, like the inherent limitations of this point, the user must master.Direct or indirect economic loss or personal injury or for improper use of

18、 the equipment provided by the company fails to perform the way I operate and caused the Company disclaims all liability or obligation. ContentsI. The instrument installation(A) Description of the hardware devices connected(B) The description of the control system hardware functions(C) Monitoring Te

19、rminal System Operating InstructionsII. The safe handling and TroubleshootingIII. After-sales serviceIV. Special instructions(A) Special instructions safety(B) The functions specified(C) Intellectual Property StatementV.Sensor calibrationI. The instrument installation(A) Hardware device connected to

20、 the running1. Connecting pipes and cryogenic liquid nitrogen biological containersConnect the liquid nitrogen and liquid nitrogen biological containers pipes, liquid nitrogen container inlet pressure should not exceed 0.5 MPa.2. Connect the power cordHas a power input and control input and output c

21、onnectors on the instrument dedicated aviation.Users choice of the power cord is not less than2.5mmsquare copper wire.Optional protective earth wire2.5mmsquare copper wire and reliably connected.If the user does not set protective earth (just touch Paul implements leakage protection), the user must

22、press the power system specification requirements specifically set up to protect our equipment grounding connection with the case.In lightning-prone areas, must have lightning protection measures.So, you can play against the computer components to prevent lightning damage may result.Note:Keep the ma

23、chine a reliable connection with the earth, to prevent electric shocks!3. The test machineFor the first time (or long useless) first control system is powered on, enter the system setup menu, the equipment testing field, manually open solenoid valves, piping system with dry nitrogen impurities blown

24、 (about 3 minutes), to prevent blockage of electromagnetic affect the normal operation of the valve, repeated several times the best, the first injection of a small amount of liquid nitrogen inside the tank to be completely cooled before the system transferred to the automatic mode, set the sensor l

25、ocation, stop 24 hours after dosing and then placed in frozen items.Note:manually open solenoid valve test is completed to remember to manually shut down.4. OperatingAccording to the temperature required for the decision into frozen time, close the lid; turn on the power, select the operating mode,

26、the device begins to work, the control system into the monitor, the system real-time display of the temperature change of liquid nitrogen tank.(B) The description of the control system hardware functionsMonitoring module section:1.Real-time monitoring of low, hightemperature.2.The running time is di

27、splayed and can start and stop solenoid valve according to the user to set the time.3. Solenoid valve control output driver,2-wayas a backup, automatic switching when the othertwo outputs invalid.Spare output terminalIOdetection.4.Paragraph2program arbitrary choices: immersion freezing, vapor-phase

28、cryopreservation.5.Using the internal LAN computer and monitor the way the tank host computer connection.Alarm module section:1.Reserved foraserial port, such as when a user needs to be equipped with a separateDTUsends alarm information.2.Low, high temperature, over-temperature alarm3. Sensor failur

29、e alarm4.The control solenoid valve relay strong electrical output No output alarm(C) Monitoring Terminal System Operating InstructionsThe system control software selected by the mode of operation, monitoring, alarm, alarm query, the query item information, goods information management, manual opera

30、tion of seven modules, the following were given detailed instructions.1. Select the operating modeAfter the system boots, enter the appropriate operating mode according to the users choice.Select the desired mode of operation; click OK to restart the system after entering the corresponding operating

31、 mode.2. The monitoring moduleReal-time monitoring of important data monitoring module Dewar indoor temperature data, the system run out of time and the system runs a variety of status. 2.1 Liquid nitrogen level valuesDisplay the current height of liquid nitrogen, in millimeters (mm).2.2 Low tempera

32、tureDisplay the current low temperature sensor, in degrees Celsius ().2.3 High TemperatureDisplay the current temperature highs sensor degrees Celsius ().2.4 OperatingDisplay the working status of each member of the runtime system.(Note: Green indicates normal, red indicates abnormal)The following f

33、igure shows the low level sensors and sensor anomalies.This user can manually open and close the solenoid valve operation, easy maintenance and auxiliary equipment test systems. 2.4.1 Low SensorShow Low sensor status.2.4.2 High SensorsHigh sensors status display.2.4.3 Level SensorsLevel sensors stat

34、us display.2.4.4 Battery VoltageDisplay battery status.2.4.5 Solenoid valve outputSolenoid valve status display, red solenoid valve opens.2.4.6 Network StatusDisplay network connection status, red means the computer loses connection with the monitoring center.2.4.7 Open stateShow open state, red lid

35、.2.4.8 Relay StatusDisplays relay status.2.4.9 Power StatusDisplay power status.2.4.10 Basic operation statusRun mode displays the current mode of running, running time display total time (non-clear), the number of liquid nitrogen tank lid to open the lid of the number of (non-clear) running on the

36、display after power program.3. The alarm messageSee all alarms recorded during device operation.4. Item informationSee details stored in liquid nitrogen tanks items.You can search to see the details of the article based on any information stored items.5. Materials managementManage storage tank items

37、 carry a library warehousing operations.5.1 Warehousing operationsBarcode scanning gun after items, items automatically get information from the monitoring center computer operator to view the information is correct confirmation, items stored in liquid nitrogen tank.5.2 Library operationBarcode scan

38、ning gun after items, the system automatically obtain items of information from the database, the operator to view and correct information to confirm the item is removed from the liquid nitrogen tank.6. System settings7. The temperature curve8. Active alarmSystem abnormalities occur during operation

39、, monitoring terminal and monitoring center computer will pop up a warning window shown below, while an alarm sounds, suggesting that duty.II. Safe handling and Troubleshooting1.Container is a high vacuum products, transportation, installation, use should be careful to avoid a collision.2.Initial fi

40、lling of liquid nitrogen, liquid nitrogen should be filled with a small amount (about 100L) pre-cooling, after close to thermal equilibrium (gasification is not severe), and then filling liquid nitrogen.3.Skin contact with liquid nitrogen can cause frostbite; the operation should note the following:

41、(1) Be sure to wear leather gloves, hands and feet can not be exposed;(2) Do not wear long traditional shoes, to avoid falling into the liquid nitrogen inside the shoe;(3) Can not bare hand contact with the rotating handle, neck and other parts of the low temperature, it is best to use other tools t

42、o turn the rotary handle when struck;(4) When filling liquid nitrogen should be in a well-ventilated place, if indoors, you should open the doors and windows to avoid suffocation from lack of oxygen caused the accident.4.Vacuum sealed container as a living connection plug can suffer accidental damag

43、e in the container, liquid nitrogen into the interlayer space vaporization dramatically boost when the sealing plug red open mouth forming relief, emissions of nitrogen, play a role in the rupture disc, ensure safe and reliable use of the product.Remove the vacuum seal is prohibited masks and vacuum

44、 sealing joints carry out any operation,such as found at the interface of any traces of artificial opening and operation, all resulting loss, the Company shall not be responsible.5.Transport should be placed in the front compartment container board position with a rope fixation, can not collide with

45、 abrasions containerisprohibitedin the case of liquid nitrogen and frozen goods loaded offtransport.6.Bottom of the vessel is equipped withfourhigh-strength casters, built-in the case of goods and frozen in liquid nitrogen, and easily move short distances indoors, indoor mobile should be careful, mu

46、st not shove thrashing prevent collisions.Moving outdoor on uneven ground is Prohibited.7. Do not allow the product surface welding.Troubleshooting and treatment methods:No.SymptomCauseTreatment1Can not turn on the powerFuse burnedThe same type of fuse replacement2Temperature display is not normalTe

47、mperature sensor is damagedReplace the temperature sensor3Machine is turned on but not coolingRefrigerant working pressure is too lowAdjust the output pressure of liquid nitrogen containers, raised approximately 0.2MPa4Refrigeration solenoid valve can not be closedClogging impuritiesBlowing dry nitr

48、ogenIII. After-sales service1.Produced theSJseries product warranty period of one year.Users must strictly follow the Product Manual provides for proper use and maintenance.During the warranty period, the user under normal conditions of use, this product is found to have quality problems, or malfunc

49、tion in use by the factory responsible for free repair or replacement of new parts; after the warranty period, the factory is still responsible for the repair, only charge fees and Accessories corresponding traffic fees.2. We have a strict service system.After receiving the maintenance notification,

50、we will response within 30 minutes, 3 days to reach the scene.Every Monday morning for my phone regularly visit time, the use of direct contact with people, to understand equipment operation and good service record.3. The company provides system software upgrades for life.Once a year for equipment i

51、nspection and issue annual reports, software upgrades only charge the cost price.4. Free for owners technical staff training 1-3.5. The company opened a 24-hour service hotline. 86-28-827241076. The following does not belong to the free warranty:(1) User unauthorized anatomy, demolition equipment;(2

52、) Damage due to force majeure, such as: disaster (earthquake / fire / flood / lightning, etc.) and abnormal voltage caused by faults;(3) Altered invoice or warranty card;(Note: the date of the warranty period starting invoicing, please keep the warranty card and purchase invoices.)(4) Due to imprope

53、r user in transport, handling and management process damaged;(5) Failure to use the manual requirements and cause damage.IV. Special instructions(A) Special instructions safety1. There must be someone on duty to ensure the safe use of the use of liquid nitrogen biological containers!2. You must open

54、 the doors and windows when using liquid nitrogen biological containers, air convection, ensure good ventilation, volatile liquid nitrogen may lead to a small range of oxygen, causing minor suffocation affect personal safety!3. Liquid nitrogen biological containers and piping connections must be str

55、ong, to eliminate nitrogen run, run, drain, drip, splash and other phenomena in order to ensure the safety of the operator!4. Stop using liquid nitrogen biological containers must be closed and the inlet valve cut off!5. Must be qualified with the use of safety grounded three-prong power outlet, make sure the ground is correct, reliable, and to ensure the personal safety!6. The use of liquid nitrogen biological containers away from heat environment must, flammable, corrosive gases and easy, strong magnetic field, dust and oil serious place!7. From the liquid nitrogen biological container