1、LED數碼管顯示的VHDL設計桂林師范高等?？茖W(xué)校羊日飛LED數碼管顯示實例運行環境n紅色颶風二代XILINX FPGA開發板 RC2-3S400 LED數碼管的板級硬件電路n四位8段式共陰數碼管1位2位3位4位位線位線段線段線LED數碼管的板級硬件電路nLED數碼管位線驅動電路qSEG_LED_S0、 SEG_LED_S1、 SEG_LED_S2 SEG_LED_S3 接FPGA相應引腳LED數碼管的板級硬件電路n8段式共陰數碼管的段碼一、LED數碼管的靜態顯示LED數碼管的靜態顯示n四位數碼管顯示相同的字符n依次顯示從0F的各個字符，每隔1s顯示一個字符。 四位數碼管器件內部復用了每位數碼

2、管的8條數據線（a,b,c,d,e,f,g,dp） 若同時將四位數碼管的位線（共陰公共端）接到低電平，則相當于同時選中數碼管的4個位。 此時若段線輸入某個段碼，則四位數碼管顯示段碼對應的同一字符。LED數碼管靜態顯示的芯片級設計框圖時鐘源50MHz分頻器計數器數碼管驅動四位LED數碼管FPGA1/50000000分頻輸出時鐘信號的頻率是1Hz，周期為1s。16進制計數器即有16種狀態，每經過1s計數值加“1”，也即跳到下一個狀態。段碼譯碼器將16種狀態碼轉換為相應的8位二進制LED數碼管段碼段碼。1/50000000分頻器（Divider）entity clkdiv is port( rese

3、t: in std_logic;clkin: in std_logic;clkout: buffer std_logic );end clkdiv;實體1/50000000分頻器（Divider）architecture clkdiv_stru of clkdiv is signal count: integer range 0 to 25000000:=0;begin process( reset , clkin) begin if reset=0 then count=0; q=0; elsif clkinevent and clkin=1 then if count=25000000 t

4、hen count=0; clkout= not clkout; else count=count+1; end if; end if; end process; end clkdiv_stru;結構體16進制計數器entity counter is port( reset: in std_logic; clock: in std_logic; countout: out std_logic_vector(3 downto 0) );end counter;architecture counter_stru of counter is signal count: std_logic_vecto

5、r(3 downto 0);begin process( reset , clock) begin if reset=0 then count=“0000”; elsif clockevent and clock=1 then if count=“1111” then count=“0000”; else count=count+ “0001” ; end if; end if; end process; countout Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y , clkin= , clkout=

6、 ); counter_m：counter port map( reset= , clock= ,countout= ); decoderledout_m：decoderledout port map( state= , Y= ); ledbits=“1111”;end led8seg_stru;三個子模三個子模塊的元件塊的元件聲明聲明resetmclki_clkreseti_clki_statei_stateledsegsLED數碼管顯示的VHDL代碼綜合結果（頂層）LED數碼管顯示的VHDL代碼綜合結果（子模塊）二、LED數碼管的動態顯示LED數碼管的動態顯示n四位數碼管顯示不同的字符，比

7、如“1234”n實現原理：n由于四位數碼管器件內部復用了每位數碼管的8條數據線（a,b,c,d,e,f,g,dp），所以若要四位數碼管顯示不同的字符，則一位顯示時（占用了段線）其它三位應該不能顯示。（通過控制位線實現）LED數碼管的動態顯示n實現原理：n由于人眼的視覺暫留效應，當循環時間很短時，人眼看到的效果如下圖所示：n動態刷新時間：q電視的場頻：50Hz，即每20ms更新一幅畫面q刷新頻率太慢則會有閃爍現象q刷新頻率太快則則亮度不夠q一般在幾ms左右作業：LED數碼管動態顯示n四位數碼管顯示不同的字符，比如“1234”修改分頻器architecture clkdiv_stru of clk

8、div is signal count: integer range 0 to 25000000:=0;begin process( reset , clkin) begin if reset=0 then count=0; q=0; elsif clkinevent and clkin=1 then if count=25000000 then count=0; clkout= not clkout; else count=count+1; end if; end if; end process; end clkdiv_stru;結構體architecture clkdiv_stru of

9、clkdiv is signal count: integer range 0 to 50000:=0;begin process( reset , clkin) begin if reset=0 then count=0; q=0; elsif clkinevent and clkin=1 then if count=49999 then count=0; clkout= not clkout; else count=count+1; end if; end if; end process; end clkdiv_stru;修改計數器architecture counter_stru of

10、counter is signal count: std_logic_vector(3 downto 0);begin process( reset , clock) begin if reset=0 then count=“0000”; elsif clockevent and clock=1 then if count=“1111” then count=“0000”; else count=count+ “0001” ; end if; end if; end process; countout=count;end counter_stru;architecture counter_st

11、ru of counter is signal count: std_logic_vector(3 downto 0);begin process( reset , clock) begin if reset=0 then count=“0000”; elsif clockevent and clock=1 then if count=“0011” then count=“0000”; else count=count+ “0001” ; end if; end if; end process; countout Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y Y = “00111111”; ledbits Y = “00000110”; ledbits Y = “