1、XN-10/20 updated information XN series Advanced TrainingSysmex CorporationCustomer Support Div.Version1.0Contents1. Service updates1.1. Service settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. S

2、A-014.2. CELLCLEAN AUTO4.3. HPCContents1. Service updates1.1. Service settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCContents1. Service updates1.1. Service sett

3、ings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCSystem operation mode change Mode 0/1/2 in a service settingsThis means operation mode A/B/C for barcode readerServic

4、e settingsService settingXNXNBarcodes are in both sampler and main unitMode ASampler module reading result must match with main unit reading result. When matching, sample will be aspiratedMode BMain module reading result is prioritized and sample will be aspiratedMode C(Only when inquiry key is rack

5、 ID and sample pos)Main module does not read barcode, sample will be aspirated by sampler module rack ID and sample posBarcode reading result can be decided by settingIPU BCRBCRBCRMode AInquiry to host by sampler module readingSampler moduleMain moduleAspirationOperationSample IDSample ID readPositi

6、ve ID checkOrder inquiryInquiry key barcode reading error settingSample IDMeasurement and demographic info.Read Read MatchedNot inquiryNot checkedAspirateSample module reading resultSample module inquiry result Not MatchedNot inquiryNot checkedNot AspirateNot measure(Positive ID check error)Barcode

7、reading errorNot checkedNot inquiryNot checkedNot AspirateNot measure(Positive ID check error)Barcode reading errorRead Not checkedNot inquiryNot checkedNot AspirateNot measure(Positive ID check error)Barcode reading errorNot checkedNot inquiryNot checkedAspirateERR.(Attribute：A)Default(No demograph

8、ic)Mode BBasically, inquiry to host by sampler module readingSampler moduleMain moduleAspirationOperationSample IDSample ID readPositive ID checkOrder inquiryInquiry key barcode reading error settingSample IDMeasurement and demographic info.Read Read MatchedNot inquiryNot checkedAspirateSample modul

9、e reading resultSample module inquiry resultNot MatchedNot inquiryNot checkedNot AspirateNot measure(Positive ID check error)Barcode reading errorNot checkedNot inquiryMeasureSee followings for details Not measureNot AspirateBarcode reading error operationBarcode reading errorRead Not checkedOrder e

10、xistNot checkedAspirateMain module reading resultMain module inquiry resultOrder not existNot checkedNot AspirateSkip measurementBarcode reading errorNot checkedNot inquiryMeasureAspirateERR.(Attribute：A)Default(No demographic)Not measureNot AspirateBarcode reading error operationMode CSampler modul

11、eMain moduleAspirationOperationSample IDSample ID readPositive ID checkOrder inquirySample IDSample IDMeasurement and demographic info.Auto setNot executedNot checkNot inquiryNot checkAspirateSample module reading resultSample module inquiry resultQ-Flag changeValue change from 100 to the wanted val

12、ueService settingsService settingsQuery to host wait timeWhen reflex rule is judged by LIS, host inquiry wait time can be changedContents1. Service updates1.1. Service settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4.

13、New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCBack upDuring main unit shutdown, backup file is automatically stored in IPU.CProgram filesSysmexXNIPUBackup filesRestore 7 back up points are selectable to be restored.Sensitivity/ Calibration/ Hardware position adjustmentSensor adjustment/ Uni

14、t counter/ Laser settingLED adjustmentNVRAMCalibrationWhen using “calibrator calibration” function, user calibration value will be changedExample: RBC_U_CALFSR can change service calibration Example: RBC_CALCAL line will appear on QC chartNVRAMCAL lineVial lineQC chartContents1. Service updates1.1.

15、Service settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCGetlog toolHow to use Getlog toolShutdown IPU program, and log off WindowsLog in Windows as “Administrato

16、r”, and close IPU programExecute “GetLog. exe”.CProgram filesSysmexTOOLSGetLog.exeEnter date when you want to take logPress outputThis tool is included program version 00-05 build 04 or over.Backup tool covers Getlog tool function.Backup toolHow to use the backup toolShutdown IPU program, and log of

17、f WindowsLog in Windows as “Administrator”, and close IPU programExecute “Backup. exe”.CProgram filesSysmexTOOLSbackup.exeClick OKThis tool is included program version 00-07 build 8 or over.Backup toolBack up filesVHDDatabase (patient info can be removed)Log filesTake log info during selected dateSa

18、me as Getlog toolRawdataTake Rawdata if necessaryRestore toolHow to use the restore toolShutdown IPU program, and log off windowsLog in windows as “Administrator”, and close IPU programExecute “restore. exe”.CProgram filesSysmexTOOLSrestore.exeContents1. Service updates1.1. Service settings1.2. NVRA

19、M 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCPCB 30001How to replaceReplace PCB 30001Execute “A/D Converter setting (Auto)” in service menuAdjust following:Sample tube sensor

20、(only for SA-01)SensitivityClogBlood sensorHGB convertHow to replaceTurn off main unitShort laser diode by short pinDisconnect cables from PCB 20001Confirm VR1 on PCB 20001 is turned to counter clockwise completelyReplace PCB 20001 and connect cablesTake out short pinAdjust followingslaser powersens

21、itivityPCB 20001PCB 20002RBC related preamp boardHow to replaceReplace PCB 20002Confirm RBC and PLT sensitivity and adjust them as neededConfirm clog level and adjust as neededPCB 20002APD moduleHow to replaceNew APD module has parameter memoReplace APD moduleExecute APD parameter settings from serv

22、ice menu and input parametersAdjust followingsOptical alignmentSensitivityLaser diodeLaser diode Turn off main unitShort laser diode by short pinDisconnect cables from PCB 20001Replace laser diodeConnect cables to PCB 20001Remove short pinExecute “Laser setting”Adjust following:Optical alignmentSens

23、itivityLaser blockReplace Laser blockExecute “Laser setting”Confirm followingsOptical alignmentSensitivityLaser blockIPUTake a back up from IPU by backup toolReplace the PCInstall IPU program into new PCProgram version must be the same as original oneSome additional software installations are requir

24、edRestore back up file by restore tool IPUContents1. Service updates1.1. Service settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCContents1. Service updates1.1. S

25、ervice settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN AUTO4.3. HPCOverview of the SA-01 Sampler SystemSA-01 is the ONE WAY sampler for XN-1000 same as XE and XT sampler.Wil

26、l be shipped in 1Q, 2012FY.SA-01 SamplerSupply parts for SA-01XN-1000 with SA-01Logo (Sampler)SA-01 Specification Sampler nameSA-10SA-01CommentsSystem nameXN-1000Connecting Analyzer TypeA1,A2,B1,B2,B3,B4Size (Total)W645D755H855W520 D680H840Analyzer + SamplerWeight (Total)78 kg70kgAnalyzer + SamplerT

27、hroughput (Around)Around 100samples/hourAround 100samples/hourCBC/CBC+DIFFNumber of Storage Samples50samples50samplesReflex TestYESNOSampler Auto StartYESNOBarcode ReaderSampler : YESAnalyzer : YESSampler : NOAnalyzer :YESSA-01: NO Rack Barcode FunctionPower cableYESNO (Not needed)Power Supplied fro

28、m AnalyzerDevice Control(Motor, Sensor etc)By IPU(PC)via USB CableBy AnalyzerDirectly Contents1. Service updates1.1. Service settings1.2. NVRAM 2. Tools2.1. Getlog tool2.2. Backup tool2.3. Restore tool 3. Parts replacement procedure3.1. Parts replacement4. New specifications4.1. SA-014.2. CELLCLEAN

29、AUTO4.3. HPCGoal of CELLCLEAN AUTOThe goal of CELLCLEAN AUTO is to provide a “walkaway shutdown” to the customer. CELLCLEAN AUTO should be applicable to all XN series, such as XN-1000, XN-2000, XN-3000 and XN-9000 including SP-10.Will be launched in 1Q, 2012FY.The specification of CELLCLEAN AUTO4mL

30、of CELLCLEAN is inside the tube.Tube is sealed with thin film. The analyzer can pierce the film.Each tube has a 13 digits unique code.The following data are encrypted and compressed into the unique code.Material code Lot numberSerial number within the lotExpiration date for useThe unique code is enc

31、oded with barcode, and barcode label is put on the tube.The analyzer/BT can recognize the CELLCLEAN AUTO by decoding the unique code.Thin filmBarcode labelHow to use CELLCLEAN AUTOThe CELLCLEAN AUTO position on the rack should be as follows;XN-2000XN-3000Note:The analyzer would alert and skip the CE

32、LLCLEAN AUTO in the following cases; Placing CELLCLEAN AUTO on the rack with different positions shown on the above.Placing CELLCLEAN AUTO with normal sample on the same rack. Once the analyzer detects CELLCLEAN AUTO on the correct position, the sampler turns to the shutdown mode. If the sampler detects the normal sample next to the CELLCLEAN AUTO, then sampler measurement abort.XN-1000How to use CELLCLEAN AUTOShutting down all ana