xxxxxxx有限公司（xxxxxCo.LTD）,,,,,,,,,,,,,,,,,,,

設備能力CMK測算表(CMKmeasurementtableofequipmentcapability),,,,,,,,,,,,,,,,,,,

表單編號/NO：,,,,,,,,,,,,,,,,,,,

"制品名稱：

Designation：",,xxxx,,"機別：

Equipment：",,xxxx,,上限/USL：,,5.15,,"群組數大小/n：

Samplesize",,5,,"日期：

Date：",,12月-20,

"測量單位

measurementUnit：",,mm,,"測量人：

Measurementstaff：",,xxx,,"中心限：

NOMINAL：",,5.04,,"總組數：

Groupnumbers：",,16,,"制造部門：

Department：",,"生產部

PD",

"測量項目：

measurementproject：",,xxxx,,,"時間：

Time：",,,下限/LSL：,,4.92,,"抽樣方法：

Samplingmethod：",,"隨機

random",FALSE,,"是否單邊公差

IfSingleSide",,

"日期/時間

Date/Time",,"12/23

9:40","12/23

9:40","12/23

9:40","12/23

9:41","12/23

9:41","12/23

9:41","12/23

9:42","12/23

9:42","12/23

9:42","12/23

9:43","12/23

9:43","12/23

9:43","12/23

9:44","12/23

9:44","12/23

9:44","12/23

9:45",合計/Total,

批號/Lot.NO.,,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,ΣX=,405.60

"樣本測

定值/

Sampleinspectionresults",1,5.05,5.07,5.09,5.09,5.06,5.10,5.06,5.07,5.08,5.06,5.07,5.09,5.10,5.07,5.06,5.08,ΣR=,0.61

,2,5.10,5.05,5.05,5.10,5.08,5.07,5.09,5.09,5.05,5.05,5.05,5.05,5.05,5.09,5.05,5.05,"測量數據判定條件

Measuremetdatajudgementstandard",

,3,5.07,5.06,5.07,5.08,5.05,5.05,5.08,5.05,5.05,5.07,5.07,5.05,5.07,5.05,5.05,5.09,>USL藍色/Blue,

,4,5.08,5.07,5.10,5.05,5.07,5.08,5.06,5.07,5.07,5.05,5.06,5.06,5.09,5.08,5.06,5.07,<LSL紅色/Red,

,5,5.10,5.09,5.08,5.06,5.07,5.06,5.10,5.08,5.06,5.07,5.06,5.08,5.10,5.06,5.07,5.06,N=,80

ΣX,,25.40,25.34,25.39,25.38,25.33,25.36,25.39,25.36,25.31,25.30,25.31,25.33,25.41,25.35,25.29,25.35,平均/Average,

,,5.08,5.07,5.08,5.08,5.07,5.07,5.08,5.07,5.06,5.06,5.06,5.07,5.08,5.07,5.06,5.07,,5.07

R,,0.05,0.04,0.05,0.05,0.03,0.05,0.04,0.04,0.03,0.02,0.02,0.04,0.05,0.04,0.02,0.04,,0.04

圖,,,,,,,,,,,,,,,,,,"數值

INSPECTIONANALYSIS",

,,,,,,,,,,,,,,,,,,A2,0.58

,,,,,,,,,,,,,,,,,,D2,2.33

,,,,,,,,,,,,,,,,,,上限USL,5.09

,,,,,,,,,,,,,,,,,,"中心限

NOMINAL",5.07

,,,,,,,,,,,,,,,,,,下限LSL,5.05

R圖,,,,,,,,,,,,,,,,,,D4,2.11

,,,,,,,,,,,,,,,,,,D3,0.00

,,,,,,,,,,,,,,,,,,上限USL,0.08

,,,,,,,,,,,,,,,,,,"中心限

NOMINAL",0.04

,,,,,,,,,,,,,,,,,,下限LSL,0.00

過程能力分析/ProcessCapabilitiesAnalysis,,,,,,,,,,,,,,,,,,,

d,,,smachine,,,CMK,,,CM,,,CMU,,,CML,,,Grade,

0.02,,,0.02,,,1.69,,,2.40,,,,,,,,,A,

備注及說明/Remarks：,,,設備變差能滿足加工要求(Equipmentvariationcanmeettheprocessingrequirement),,,,,,,,,,,,,,,,

編制：