1、最新 料推薦模具常用英語！2008 年 09 月 12 日 星期五 15:56模具英語句子1 XXX！你現在有空嗎，我可以問你一些問題嗎？Could I ask you some questions if you are free? / Are you free now? May I ask you some questions (a question)?2 請問此產品的面是否為外觀面？表面做什么處理？是曬紋/ 拋光？Can you tell me whether the surface of this part is a visible/esthetic one? What will we

2、do for itssurface? Texture or Polishing ?3 請問產品這個面可否加頂針或頂塊？產品允許加扁頂針嗎？Does this part need an ejector pin or an ejector bar? Can we add an ejector blade?4 這個產品的柱位我們打算做司筒。（或鑲針）可以嗎？Can we add ejector sleeves or ejector pins in the boss of this part?5 產品的這個位置不能出模，我們打算做行位，在此面上會有分模線，你接受嗎？ Theres an undercu

3、t at this position and it needs a slider. It will also have a parting line onthis side, is that OK?6 產品里面的這個位置我們打算做斜頂或內行位，有問題嗎？We will make the lifter and (inner) slider in this position, will that be a problem?7 你提供的 2D產品圖與 3D產品圖不一致，請問以哪一個圖面為準？The 2D and 3D drawing you provided is not the same, can

4、 you tell me which one is correct?8 你提供的 3D產品圖有的地方?jīng)]有出模角，有的地方膠位太厚，有的地方膠位太溥，這些產品問題我們可以自己修改嗎？修改后會給交給你確認。There is no draft angle in the 3D drawing, some materials are too thick, and some place are toothin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we mo

5、dify it.9 按你們提供的縮水率千分之五，這個模具的尺寸已經做到了模具圖面要求。但注塑出來的產品不符合你們的產品圖。請確認你們的材料的縮水率是否正確？According to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right?10 產品的這個位置太小，導致模具鋼料太溥，能夠加寬這個位置嗎？This positi

6、on is too small and will make the steel material here too thin, can we widen it here?1最新 料推薦11 斜頂與后面的柱位空間太小，斜頂在運動時會干涉到柱子，能移動這個柱子的位置嗎？The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss.12 這個筋骨位膠厚太溥， 而且高度偏高， 注塑時很難填充這個筋位， 可以增加這個筋骨位的厚度嗎？The rib

7、 here is too thin and on the high side, so it will be difficult to fill here when wedo theinjection, can you increase the thickness of this rib?13 你是想將此筋骨位的高度加高 / 減低嗎？加膠的位置我們將用銅公放電加深。但減膠的位置有兩種做 法， 1、做鑲件； 2、燒焊；因?yàn)殍偧牡撞坑羞\(yùn)水，我們簡單的做法是燒焊處理，你可以接受嗎？ Will you increase/decrease the material on this rib? We wil

8、l use EDM if you add material, butthere are two option if you choose to decrease: 1. Make inserts;2 Welding, because there is water in the bottom of the insert, is that OK?14 這個樣板的筋骨位底部燒焦，是因?yàn)榕艢獠涣迹覀兛梢栽诮罟俏坏闹虚g增加一個鑲件。This sample has been burned in the bottom because the venting is not good, we can add

9、an insert in the middle of the rib.15 重做鑲件大約需要5-6 天時間，你能接受嗎？It will take about 5 or 6 days to redo the insert, is that OK?16 產品的這個面我們已經做了曬紋處理，如果需要加膠，這個面我們需要重新外發曬紋?？赡苄枰獛滋斓臅r(shí)間。所以我們直接以銅公放電的火花紋取代你要求的紋路，你可以接受嗎？We have made the texture on this side, if we add material, it will take some days to remake thet

10、exture by out-resourcing, so we suggest using the texture by EDM instead, is that OK?17 模具是用公制 / 英制的配件？需要備用件嗎？Is this mold dimension measured in inches or meters? Does it need spare parts?18 模具上銘牌上的刻字內容是由你們提供嗎？你們什么時候可以這些刻字資料。Will you provide the engraving content of the plate of this mold to us? Whe

11、n will you send it?19 可否提供此模具生產時，注塑機的型號及相關資料。如：啤機大小、呵林柱尺寸、頂棍孔尺寸等 Can you provide the type of injection machine and other related information of this mold to us?Such as the boss dimension, the holes dimension of the ejector pin and the size of the injection machine and so on.20 這個問題我需要同其它同事商議會再答復你。I

12、need to discuss this problem with the other colleagues and then I will reply back to you.21 我們將盡力達成你的計劃，如有異常，會及時通知你。We will try our best to complete your plan, if there are any complications, we will notify2最新 料推薦youimmediately.22. 這個產品的長度為 330.12MM,寬度為 78.96MM,高度為 45MM膠.厚為 2MM,重量為 70.63g, 試模注塑機型號為

13、250 噸, 膠料顏色為黑色 , 產品外表面曬紋處理 , 內表面為拋光 . 需要日期章、環保章、材料章 . 前后模用 2344 氮硬，斜頂和行位座用 738H，以上模具信息正確嗎？請確認！The length of this part is 330.12MM, Width is 78.96MM, height is 45MM,thickness is 2MM,weight is 70.63g, the injection machine is 250T, the material is black, the outside of the part hastexture, inner side

14、needs polishing, and it also needs a date and recycle stamp ,the core & cavity is 2344 nitridng, the lifter and slider shelf is 738H. Please check the information above!23 現在到了吃午鈑的時間，我們下午再繼續好嗎？It is time to have lunch, lets discuss this project later this afternoon?24. 和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動(The und

15、ercut area interferes with the slide block and needs to be filled with material to help the slider move smoothly.)25. 加肉太多(The thickness added is too thick.)26. 加肉面積太大 (The thickening area is too wide.) 27.GATE位置移位 ( The gate position is moved.)28. 滑塊拆的位置 (The split line of slide block or the area o

16、f slide.)29. 此處有尖角，填充困難 (It is hard to fill this area due to the sharp feature.)30. 此處鋼材太薄，強度不足而且不容易冷卻(The strength of this area is too weak and it is hard to cool because the steel is too thin.)31. 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷(We avoid designing the semicircle of the cylinder on the slide block b

17、ecause it will be pulled apart or cause drag marks.)32. 此處做斜銷在作動時會削到成品肉厚(The part will be damaged if we make the lifter in this area.)33. 這個面是裝配面，不能加料(This is a critical surface where we cannot add additional material.)34. 此處料位太厚，會有縮水，建議減料改善(Because of the shrinkage of the thickness, we suggest redu

18、cing some wall thickness to improve it.)35. 此面是不是外觀面，此處做滑塊的話會有夾線，是否可以接受(Pleaseconfirmwhether itis a criticalsurfaceor not.Also,confirm whether itis acceptable3最新 料推薦tohave a slide split line if we have a slide in this area. )36. 此處有倒勾，能否減料，使公母?？科疲蛔龌瑝K和斜銷(Please confirm whether we can reduce material

19、 to the area where we have an undercut as indicated to have shut off on cavity side. No slide block and lifter will be made. )37. 請盡快確認這種拆模方式和結構，否則會影響模期(Please confirm the issues of Parting line, Gate position.Etc. as soon as possible; otherwise, the lead-time will be extended.)38. 此面是否有特殊要求，能否有頂針印(

20、Please confirm whether it is a critical surface or not and if we can have E.J. pin marks on it.)39. P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響(There are sharp edges if we set the parting line here, It will reduce the tool life)40. 加大拔模角，以便脫模順利 We suggest enlarging the draft angle to help release the tool.)41. GAT

21、E 做在此處的話有兩個缺點： 1. 蓋子打開時可以看到 GATE的修剪部位 ; 2. 兩個斜銷在同一側，頂出也不是很平衡 .(There are two problems if the gate is to be designed in this area: a). It is easy to see the gate mark when you open the cap.b). The ejectors are unbalanced when two lifters are on the same side)42. GATE 做在此處的話 . 蓋子打開後看不到 GATE的修剪部位(The g

22、ate mark is not visible if the gate position is designed like this.)43. 如果 GATE一定要做在你們指定的位置的話，那還不如做在這一側，這樣的話還可以減小這個位置的縮水(If you insist that the gate position has to be like the original design, then we would further recommend to have it to the area indicated so it can avoid a shrink problem in this

23、area.)44. 在此處 GATE做潛頂針的話，背後的外觀面會有沖料痕，而且成品又是黑色的，會最明顯(If the design of the gate has to be a sub. Gate, then the back surface of the part will have serious flow marks due to the black color.)22. P.L開在此處不合理，模具加工困難， P.L 應改為和圖示的一樣(Thisarea is not suitable to have a Parting line because the toolwill become

24、more complicated;therefore, we recommend to have the Parting line as indicated.)45。產品粘母模的機會很大，能否在公模加倒勾，拉料頂針或者公模保留E.D.M 紋，開模時使成品留在公模一側(Thereis possible sticking on cavity; therefore, please confirmwhether it can makeundercuts,snatch pins or leave coarse E.D.M. on the core to snatch the part on)4最新 料推

25、薦46. 此處料厚段差很大，成品表面會有應力痕，是否接受(Please confirm whether it is acceptable to have stress lines on the surface because the thickness is not equal.)47. 請注明何處為外觀面，能否提供 2D圖和注意事項(Please advise where the critical surface is. Please also provide us a 2D drawing with critical dimensions. )48. 紅色所示處是有問題的地方，請?zhí)貏e注意(

26、Please note the red highlights because those areas have problems.)49. 成品設計此處有問題，建議如下圖所示修改(We would suggest using the attached part design as the current design has problems.)50. 此處改為一個球形的凹槽(We suggest modifying it as a globe recess.)51. 圓柱特征要有一半不可以拆在滑塊裡，以防拉斷(this issue is the same as no.31)52. 此處大滑塊

27、上走小滑塊，小滑塊要先退，大滑塊要做延遲(The inside small slide block will recede first and the parent slide block have to postpone sliding.)53. 滑塊要用液壓油缸抽芯以保証開合模順序(The slide pins will use an oil cylinder to assure that the process is in proper order.)54. 這個面有裝配，加料的話裝配時會頂住，如圖所示(We cannot add material to this surface bec

28、ause it will intervene between the two parts when it is assembled. Please see the sketch attached. )55. 可降低斜銷面，增加成品些許肉厚來做變化(To descend the surface of lifter in order to thicken the part.)56. 一半做斜銷，一半做自然(One half side will have the lifter and the other half will be solid/nature.)57. 此處兩個柱子重疊，有倒勾，不能做自

29、然，要做SLIDE(These two bosses are overlapping with undercut therefore it can not be made as solid. We suggest making it with a slide block.)58. 此處強迫頂出 (This area needs force ejection.)59. 公模兩段開模，這個地方先退 (Here will be a double ejection for forward and receding.)60. 此處做鑲件會有夾線，能否接受Please confirm whether it

30、 is acceptable that there will be a split line here.)5最新 料推薦61. 此面公母模 1 度靠破，會有段差，可否接受(Please confirm whether it is ok to have mismatch to the area where there is 1 degree of shut off in Core / Cavity side.)62. 這個尺寸能否加大 (Please confirm whether we can enlarge this dimension.)63. 此處加一個凹槽，膠片的彈出效果會更好一些，試

31、模後看裝配的效果再做修正(It will affect the elastic of the film better if we add a recess. See how it will affect the assembly parts, and then make your decision.)64. 此處有倒勾，建議將剖面線所示部位 CUT即可避免此處的倒勾(There is an undercut here, we suggest cutting out the indicated part as it highlighted to avoid an undercut.)65. 成型

32、後 SUB GATE要修平(The gate (sub gate) needs to be trimmed evenly after being moulded.)66. 此處倒勾先垂直頂出，之後再手動取出(This area of the undercut needs to be ejected vertically, then taken out manually.)67. 這兩個面都有滑塊， GATE改在此處改不到(The gate is not suitable in this area because there are two sliding blocks sealing off

33、this area.)68. 此處加做一個旋轉 GATE，射出時方便調整成品的品質(We would suggest placing a runner shut-off insert to adjust the volume of part filling.)69. 此倒勾在滑塊上強迫脫模，倒勾是否可以減小到0.6(Thisundercutwillbe forceejectedout,Please confirmwhether itcan be reduced to 0.6 mm.)70. 此柱子無法脫模，請確認是否是在轉圖時錯位，能否提供客戶的原始圖檔 data. ) (This boss

34、is not releasable. Please check the file again and if possible, pleas re-send us theoriginal draft71. 此柱子是實心的，會縮水 (This boss will shrink because it is a solid boss.)72. 這個面是否要咬花，咬花番號是什麼，最小的拔模角要多大(Please confirm whether this surface needs to be textured or not. Please advise texture specs. Also, what

35、s the min. draft. )73. 這個面是否要打光，貼標簽(Please confirm whether this surface needs to be polished and stuck on a sticker.)74. 紅色顯示的幾個面拔模角太小，出模時會拉傷，建議加大拔模角(The red highlighted area has a problem of a small draft angle. Wesuggest enlarging thedraft to avoid causing drag marks on the part.)6最新 料推薦75. 此 RIB

36、太薄，會填充不足 (This rib can not be filled properly because it is too thin.)76. 此 RIB 太厚，會縮水 (This rib will have a shrink problem because it is too thick.)77. 此處倒勾出模困難，建議先不做倒勾，成型後再二次加工，但要做治具，費用要另外算(There are problems with this current design, we recommenddoing this undercut as an alternative but there wil

37、l be additional costs.)78. 柱子底部都要做火山口(The base of all bosses require a crater to avoid shrinkage.)1. 鑲件， P.L. 面有充足排氣坑， P.L. 面要開環形排氣槽 , 并能將氣體排到模外。Insert/PL should have adequate venting, PL should have around slot for venting.79. 頂棍孔鑲件端面距離底板面 0,5mm,攻 m20牙 ;the surface of KO insert should below bottom

38、plate 0.5mm,thread M20.80. 回針，中托司與模胚部份避空 0.5mm； RP,EGP should have 0.5mm gap with the moldbase.81. 排氣槽距封膠位 10-15mm；Venting slot distance from the seal off position 10-15mm82. 運水進用 E ，運水出用 S；In take E, Out take S83. 底面板均要有隔熱板 ,DME規格 1/4 厚；Top/Bottom plate must have insulator plate, DME standard 1/4H8

39、4. 吊環要在模具的重心（保證吊模時的平衡） ; Eyebolt should on the center of the mold(for balance)85. 吊模螺絲的位置要在前 / 后模部份的重心 , 保持平衡；The eyebolt position on the cavity/core side should on the center of gravity for balance86. 唧嘴分試模唧嘴 / 走模唧嘴 ; Sprue type: Trial/Delivery87. 喉塞選用： NPT規格 ;Plug use NPT spec.88. 中托司采用 HASCO滾珠形式

40、.Use HASCO ball EGP89. 水咀采用法國標準 :1/4 的水咀寫 :RPL08-1151 Jiffy Use French Standard: 1/4 mark:RPL08-115190. 全部使用英文和英制單位 All in English& Imperial Unit7最新 料推薦91. 請檢查內模尺寸有否乘縮水? Are part dimensions to print plus shrink?92. 凡有電線通過的角位要改為R角，是否完成 All wires protected from sharp corners？93. 所有替換的元件必須是標準件。 All rep

41、laceable components must be standard components.94. 是否加啤塑總計器？ Add shot counter?95. 一個復雜的模具，設計經過周詳考慮，成功地克服了各種設計上的限制。A complicated mould with thorough design consideration to overcome the numerous design constraints.96. 所有移動的零件應使用硬鋼料，行位必須用硬墊板和硬線條，而且必須有限位及定位鎖。All moving components shoulduse hardened st

42、eel: all slides should be installed withhardenedor lubricated alloy wear plates and gibs, and with positive slide retainer.97.BOM的內容應包含運水接頭 , 頂針和自制的零件 .BOM including water fittings, ejectors &custom components.98. 若沒有運水回路，斜頂為鈹銅。BeCu for lifters if w/o water circuits。99. 對應的部件在前、后模平面視圖中鏡像 Correspondi

43、ng components mirrored at core &cavity100. 有否省光就出模 ?Check polish for line of draw finish？Core pull slot mechanism installed and O.K.101. 模具須用多大吊機才可搬動Crane capacity and loading clearance.。102. 經流道及變形電腦模擬分析。 Conduct mold flow &mold warp analysis.103. 散件圖或 3D模具圖 Component and/or 3D mould design drawing

44、.104. 若尺寸不重要，適量冷卻也可。 Cooling less important when dimensions are not important.105. 將一個標準四模腔大水口模具與一個四模腔倒轉大水口模具結合成為一套可于同一大小的注塑機，生產量可增加一倍的層板模具，并且可降低成本。Combine a traditional 4 cavity edge gate and a4 cavities reverse gate moulds which help to double the molding capacity and reduce production cost.106. 此

45、模具最大的特式是，可將模具分開變成兩套，在不同地方生產，增加生產的靈活性。Can be separated into two individual moulds for molding in two different mould shops.107. 由于全套模具均利用模具標準零件制成，在維修及換零件上比較方便。Consists of all standard mould components which facilitate mould maintenance.108. 出模方向的標示Die draw called out8最新 料推薦109. 標出前、后模距離，滑動部件滑動距離和塑件脫離

46、的位置Dimension all the opening , travel & clearance110. 是否使用 DME運水接頭及編號 ?DME egg. Water fittings recessed and marked?111. 開箱后是否容易吊出模具及是否分開前 / 后模運輸？Delivery right side up , or in two halves？112. 吊?？壮叽纾胶?， 2 邊都要有 Eyebolt size and balance in 2 sides113. 出行程、行位、斜頂行程的標注Ejection stroke & slide, lifter trave

47、l dimensioned。114. 若有斜頂，做出分析。 Ejection study if lifter adopted115. 頂出到極限位置。 Ejection extended at the most116. 頂針導柱的安裝Ejector guide pins installation .117. 重量大于 50lbs 的鑲件必須要有吊?？?。 Eyebolts for inserts more than 50lbs.118. 邊緣型或直入型水口都可以接受。Edge gate or sprue gate requiring secondary operation acceptable.

48、119. 斜頂和與其接觸的內?；蜩偧谟捕壬嫌?4 度的差別（ HRC）。4 point in HRC different to lifters contacting or cavity steel。120. 水口及水口頂針的 4 倍放大視圖，按實際尺寸標注。4X size section, dimensioned to reflect the actual size.121. 常規、安全和搬運要求 General ,safety and handling122. 建議模具用于鎖模力超過 100 噸的注塑機，或有 1.5mm以下的頂針或頂出行程超過 50mm時，應裝上頂針板導柱。Guided

49、ejection recommended for mould above 100 tons clamp capacity, ejector pins of 1.5mm or smaller, or ejector stroke longer than 50mm.123. 邊釘插入模板有否頂著及加疏氣空 ?Guide pin cleared and vented?124. 鑲件定位和編號以防止不正確的組裝。Inserts keyed and numbered to prevent incorrect assembly.125. 斜面角度要比行位斜邊角度大3 度(25 度 ) 。Jaw angle

50、 3 deg.more than angle pins(25 degree).126. 在行位、斜頂、主要鑲件處保留足夠位置（空間）布置水槽。Keep enough space to run waterline at slide /lifter/major inserts.127. 斜頂角度小于 15 度。 Lifter angle less than 15 degree.128. 斜頂桿直徑不能少于 1 。Lifter rods dia, less than 19最新 料推薦129. 是否已安裝限位制？ Limit switch in tact and protected.130. 模坯和鋼

51、料號的標注 Mold-base and steel dimensioned131. 斜頂鑲件最小 5 度插穿 Minimum 5 deg.for shut-off.。132. 動作機構是否正確？ Mechanism for sequence133. 是否已安裝安全帶及噴上正確顏色在模坯上？Mold safety straps installed and painted red？134. 適宜應用模擬的模具注塑過程，注射分析、壓力分布及溫度分布以確定最佳入水位置、流道尺寸和疏氣位置等。Mould flow and simulationshould be carriedout for thebes

52、t gate location,filling analysis,pressure distribution and heat distribution.135. 模具在設計上要做到盡快冷卻，上、下內模高溫點應該有個別的冷卻，應有適量頂針。Mould should be designedwith maximum cooling andwith appropriateamount of ejectionpoints.136. 模具能夠全自動生產，大的零件應由機械手拿出。Mould should be able to run fully automatic. Large part should b

53、e picked up by robot.137. 模具經過測試，符合預定的 Cpk 質量標準。Mould should be tested to meet a defined Cpk quality standard.138. 模具應具備可以預防意外損害及錯誤安裝等安全特性。Mould should have safety features to protect accidental damage, incorrect assembly and set up of mould.139. 上、下模需要精確配合或有擦位的地方，模具一定要有直身鎖。Mould halves requiring accurate alignment of core and cavity, and shut off should have appropriate part line loc