1、KPI指標分析與處理 2005年5月,切換成功率公式1 切換成功率公式2,KPI指標公式,KPI指標公式,無線接通率公式1 無線接通率公式2,KPI指標公式,全網掉話率公式1 全網掉話率公式2,KPI指標監測,OMCR自定義PM監測模板 觀察全網KPI指標情況，收集并排序小區級KPI指標，分析掉話最高或擁塞最嚴重的的510個小區，定位故障原因，派發排障工單。 利用GETPM工具 利用MotoANS系統。,檢查掉話小區是否連接有直放、功放等設備 檢查掉話在該小區的載頻上分布情況 檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等） PB2或奇偶值 IOI5或單

2、個載頻明顯偏高 利用Perf工具過濾Ma_fail_from_ms高的載頻 檢查掉話小區的周圍小區是否存在斷站情況 檢查掉話小區周圍基站是否擁塞嚴重,高掉話小區處理思路RF掉話,小區內切換掉話 檢查掉話小區是否連接有直放、功放等設備 檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等） 利用Perf工具過濾Ma_fail_from_ms高的載頻 檢查掉話小區的周圍小區是否存在斷站情況 檢查掉話小區周圍基站是否擁塞嚴重 檢查切換參數設置是否合理,高掉話小區處理思路切換掉話,高掉話小區處理思路切換掉話,BSC內部切換掉話 檢查掉話小區的Per Carrier統計

3、項（Path_balance、BER、IOI等） 統計其鄰區的IN_INTRA_BSS_HO_RETURN值 檢查上述統計項（切入返回）高的小區的Per Carrier統計項。 打開Per Neighbour的統計項，檢查切向哪個鄰區的成功率較低 檢查掉話小區的周圍小區是否存在斷站情況 檢查掉話小區周圍基站是否擁塞嚴重 檢查切換參數設置是否合理和周圍小區有無同BCCH、BSIC的小區,BSC之間切換掉話 檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等） 檢查鄰區切換信息如LAC、Cell ID、BCCH、BSIC等設置是否有誤 統計其鄰區的IN_INTR

4、A_BSS_HO_RETURN值 檢查上述統計項（切入返回）高的小區的Per Carrier統計項。 打開Per Neighbour的統計項，檢查切向哪個鄰區的成功率較低 檢查掉話小區的周圍小區是否存在斷站情況 檢查掉話小區周圍基站是否擁塞嚴重 檢查切換參數設置是否合理和周圍小區有無同BCCH、BSIC的小區,高掉話小區處理思路切換掉話,RF掉話相關參數,上行（Up link) LINK_FAIL：不能解碼減1，恢復加2；變?yōu)?，停止發射 LINK_ABOUT_TO FAIL：確定BTS、MS何時滿功率發射 T3109：釋放TCH參數 下行（Down link) RADIO_LINK_TIME

5、OUT ：不能解碼減1，恢復加2；超時MS停止發射 T3109必須大于Radio_link_timeout，防止兩個手機同時占用同一個TCH信道產生串話現象 FULL_PWR_RF_LOSS設置為1,切換類型和優先級別,Uplink quality Uplink interference Downlink quality Downlink interference Uplink rxlev Downlink rxlev Distance PBGT,由高到低,切換參數設置averaging,切換參數設置averaging,Hreqave/Hreqt的設置 參數修改命令格式 chg_cell_el

6、ement rxqual_dl_ho, 0 0 4 6 0 0 0 LAC CellID Enter hreqave: 4 Enter hreqt: 3 Enter w_qual: 1 參數查看命令格式 disp_element rxqual_dl_ho, 0 37 cell_number =4 6 0 0 0 31122 4153 rxqual_dl_ho0 = alg_num: 0 alg_data: 4 3 0,切換參數設置Rxqual,下列參數設置決定是否做RXqual切換： ul_rxqual_ho_allowed : 上行RXqual切換控制開關 dl_rxqual_ho_allo

7、wed : 下行RXqual切換控制開關 chg_cell_element rxqual_dl_ho, 0 0 4 6 0 0 0 LAC CELLID chg_cell_element rxqual_ul_ho, 0 0 4 6 0 0 0 LAC CELLID decision_1_n6/decision_1_p6：滿足切換門限的測量報告數目 （經過平均過的）大于等于P6 l_rxqual_dl_h： RXqual切換控制門限 l_rxqual_ul_h： 命令格式 chg_element decision_1_n1 ,切換參數設置Interference,下列參數設置決定是否做RXqua

8、l切換：. interfer_ho_allowed : 切換開關 chg_cell_element rxlev_ul_ho, 0 0 4 6 0 0 0 LAC CELLID chg_cell_element rxlev_dl_ho, 0 0 4 6 0 0 0 LAC CELLID N7 must be greater than or equal to P7. N7 must be less than or equal to the hreqt value set using chg_cell_element rxlev_ul_ho command for rxlev_dl_ho andrx

9、lev_ul_ho. decision_1_n7/decision_1_p7 thresholds: u_rxlev_dl_ih/u_rxlev_ul_ih 切換門限,interfer_ho_allowed 開關參數 intra_cell_handover_allowed 開關參數 chg_cell_element rxqual_ul_ho, 0 0 4 6 0 0 0 LAC CELLID chg_cell_element rxqual_dl_ho, 0 0 4 6 0 0 0 LAC CELLID chg_cell_element rxlev_ul_ho, 0 0 4 6 0 0 0 LA

10、C CELLID chg_cell_element rxlev_dl_ho, 0 0 4 6 0 0 0 LAC CELLID n6/p6 n7/p7 判決條件 u_rxlev_ul_ih/u_relev_dl_ih l_rxqual_ul_h/u_rxqual_dl_h 切換門限 hop_count 切換次數 hop_count_timer 時間（SACCH）,切換參數設置Intracell,切換參數設置PBGT,pwr_handover_allowed 開關參數 Use_neighbor_pbgt_hreqave 1=use hreqave in add_nei 0=use hreqave

11、 in add_cell PBGT(n) ho_margin_cell 切換門限,切換參數設置擁塞釋放,ho_exist_congest mb_tch_cong_thres congest_ho_margin bounce_protect_margin bounce_protect_cong_tmr If there is no free TCH available when an assignment request is coming in, it is possible to handover existing calls to neighbor cells and free TCHs

12、for new coming calls If ho_exist_congest = 1, handover as many calls as the number of queued assignment requests If ho_exist_congest = 2, handover as many calls as that meet congestion relief criteria,切換參數設置 其它,en_incom_ho enable incoming handover inter_cell_handover_allowed ms_distance_allowed : en

13、able distance handover decision_1_n8/decision_1_p8 thresholds: ms_max_range the ms_max_range is also used by RRSM to reject Channel Requests from distant mobiles. This feature is enabled by chg_element poor_initial_assignment bounce_protect_margin bounce_protect_qual_tmr,功率控制RXqual,The following par

14、ameters will determine if the power control has to be done due to rxqual. for power increase: decision_1_n3/decision_1_p3 for power decrease: decision_1_n4/decision_1_p4 uplink thresholds: l_rxqual_ul_p/u_rxqual_ul_p downlink thresholds:l_rxqual_dl_p/u_rxqual_dl_p,功率控制Rxlev,The following parameters

15、will determine if the power control has to be done due to rxlev. for power increase: decision_1_n1/decision_1_p1 for power decrease: decision_1_n2/decision_1_p2 uplink thresholds: l_rxlev_ul_p/u_rxlev_ul_p downlink thresholds: l_rxlev_dl_p/u_rxlev_dl_p,功率控制參數MS,ms_power_control_allowed enable/disabl

16、e MS power control, if disabled, the MS transmits in max_tx_ms. ms_p_con_interval (0-31 , 1 step= 2 SACCH multiframes,default=2) the minimum time in BSS interval between successive power control commands. ms_p_con_ack (0-31 , 1 step= 2 SACCH multiframes,default=2) when the MS is sent a new power con

17、trol message, it will change transmit power and then echoes an ack message. The ms_p_con_interval will only be started when ack has been received or this timer has expired.,功率控制BTS,bts_p_con_interval bts_p_con_ack for BTS power control, same as the previous one. bts_power_control_allowed if disable,

18、 the BTS transmits in max_tx_bts,功率控制步長,pow_inc_step_size_ul pow_inc_step_size_dl sets the step size for uplink and downlink power increase in dB pow_red_step_size_ul pow_red_step_size_dl sets the step size for uplink and downlink power decrease in dB,功率控制rapid pwr down,rapid_pwr_down enable/disable of this feature 0 = OFF