1、H3CTE分解試驗V1.0PS:為了參考！而整理的，希望對各位準備參加的同學有所幫助，其中也不乏之處，Isolate-user-VLAN 實驗拓撲要求Pc1 處于 vlan10，pc2 處于 vlan20，pc3 處于 vlan30要求 pc1 和 pc2 可以pc3配置將連接各 pc 的接口加入相應 vlansw1 與 sw2 之間接口為 acsw2 與 sw3 之間接口為 acs 加入 vlan20 s 加入 vlan30在 sw2 上將 vlan30 設置為 Isolate-user-VLAN，vlan10，vlan20 為 secondary vlan系統自動將 vlan10 端口改為

2、 hybrid 接口，允許 vlan10、30 通過將 vlan20 端口改為 hybrid 接口，允許 vlan20、30 通過將 vlan30 端口改為 hybrid 接口，允許 vlan10、20、30 通過Sw1vlan 20#erface Ethernet0/4/0port link-mode bridgeport acs vlan 20#erface Ethernet0/4/1port link-mode bridgeport acs vlan 20sw2#vlan 10 #vlan 20 #vlan 30isolate-user-vlan enable#erface Ethern

3、et0/4/0 port link-mode bridge port link-type hybrid undo port hybrid vlan 1port hybrid vlan 10 30 untagged port hybrid pvid vlan 10#erface Ethernet0/4/1 port link-mode bridge port link-type hybrid undo port hybrid vlan 1port hybrid vlan 20 30 untagged port hybrid pvid vlan 20#erface Ethernet0/4/2 po

4、rt link-mode bridge port link-type hybrid undo port hybrid vlan 1port hybrid vlan 10 20 30 untaggedport hybrid pvid vlan 30sw3#vlan 30#erface Ethernet0/4/0port link-mode bridgeport acs vlan 30#erface Ethernet0/4/2port link-mode bridgeport acs vlan 30PSIsolate-user-VLAN 采用二層VLAN 結構，它在同一臺設備上設置Isolate-

5、user-VLAN 和Secondary VLAN 兩類 VLAN。Isolate-user-VLAN 用于上行，不同的 Secondary VLAN 關聯到同一個 Isolate-user-VLAN。上行連接的設備只知道 Isolate-user-VLAN，而不必關心 Secondary VLAN，簡化了網絡配置，節省了 VLAN 資源。Secondary VLAN 用于連接用戶，Secondary VLAN 之間二層報文互相。一個 Isolate-user-VLAN 可以和多個 Secondary Secondary VLAN 對上行設備不可見。VLAN 相關聯。Isolate-user-

6、VLAN 下面的故障點1、 vlan 未創建，display vlan 查看是否創建2、 端口未允許 vlan 通過，display vlan X, display否 tagged 通過port trunk 查看允許通過的端口，以及是3、 端口類型錯誤，display brief 4、 三層接口配置，display iperface /displayerface brieferface brief5、 vlan，display vlan X6、 與子接口互通時，本端要使用 trunk 接口，允許 vlan x 通過，且子接口要封裝 vlan xStp拓撲要求Vlan1 to 100要求實現流量

7、負載分擔，sw1，sw2 分別為主根配置創建 vlan開啟 stp創建 mstp 域并激活端口設置為 trunk，放行需要負責分擔的業務 vlan，設置實例主備根Sw1#vlan 1 #vlan 2 to 100 #stp instance 0 root primary stp instance 1 root primary stp instance 2 root secondarystp enablestp region-configurationregion-name h3c instance 1 vlan 1 to 50instance 2 vlan 51 to 100 active r

8、egion-configuration #erface Ethernet0/4/1 port link-mode bridge port link-type trunkport trunk permit vlan 1 to 100#erface Ethernet0/4/2 port link-mode bridge port link-type trunkport trunk permit vllsw2vlan 1#vlan 2 to 100 #stp instance 1 root secondary stp instance 2 root primary stp enablestp reg

9、ion-configuration region-name h3c instance 1 vlan 1 to 50instance 2 vlan 51 to 100 active region-configuration #erface Ethernet0/4/1 port link-mode bridge port link-type trunkport trunk permit vlan 1 to 100#erface Ethernet0/4/3 port link-mode bridge port link-type trunkport trunk permit vlan 1 to 10

10、0sw3#vlan 1 #vlan 2 to 100 #stp enablestp region-configuration region-name h3c instance 1 vlan 1 to 50instance 2 vlan 51 to 100 active region-configuration #erface Ethernet0/4/2 port link-mode bridge port link-type trunkport trunk permit vlan 1 to 100#erface Ethernet0/4/3 port link-mode bridge port

11、link-type trunkport trunk permit vlan 1 to 100PS1、查看后發現沒有實例 2 的端口，可能是端口沒有讓 vlan 通過,通過display port trunk 查看，修改為 permit vlan 1 to 1002、查看后發現端口為 mast 狀態，表明出現了多域，檢查 stp 域配置，修改為一樣Stp 保護全局配置，防止 tc 大量發送導致系統故障stp tc-protectionstp bpdu-protection全局配置，當配置了邊緣端口的端口收到 bpdu 報文時，將其 down在根端口收不到 bpdu 報文時，將其關閉，同時阻塞端口

12、開始轉發數stp loop-protection據，防止環路產生stp edged-port enable邊緣端口，快速切換到 forwarding 狀態，下掛 pc，收到 bpdu 報文后轉為轉發狀態當收到 bpdu 報文的優先級優于現在的根優先級時，將其抑制stp root-protection故障點1、 stp 未啟用，display stp brief 查看其狀態為 disable2、 stp 模式不同，display stp 可顯示其 mode：stp、rstp、mstp3、 端口未放行業務 vlan，display port trunk 查看狀態為 trunk 的端口和允許通過的

13、vlan4、 mstp 域配置，display stp region-configuration，顯示、實例關系、修訂級別，注意：當修改域配置后要重新激活才能生效：active region-configuration5、 stp 根設置錯誤，display stp root、display stp instance x 顯示當前實例根選擇，6、 為端口配置 cost 值，人為阻斷某個端口，不能阻斷根橋上的指定端口，stp cost 1000， display stp brief 查看端口狀態7、 stp 保護配置，display cur 查看鏈路聚合實驗拓撲配置命令R1 端：Vlan 2er

14、face Bridge-Aggregation1 port link-type trunkport trunk permit vll#erface GigabitEthernet1/0/1port link-mode bridge port link-type trunkport trunk permit vllport link-aggregation group 1#erface GigabitEthernet1/0/2port link-mode bridgeport link-type trunkport trunk permit vllport link-aggregation gr

15、oup 1erface GigabitEthernet1/0/32port link-mode bridgeport acs vlan 2stp edged-port enablestp bpdu-protectionstp enableR2 端：Vlan 2erface Bridge-Aggregation1 port link-type trunkport trunk permit vll#erface GigabitEthernet1/0/1port link-mode bridge port link-type trunkport trunk permit vllport link-a

16、ggregation group 1#erface GigabitEthernet1/0/2port link-mode bridge port link-type trunkport trunk permit vllport link-aggregation group 1erface GigabitEthernet1/0/32port link-mode bridgeport acs vlan 2stp edged-port enablestp bpdu-protectionstp enable查看：R2disp link-aggregation summaryAggregationerf

17、ace Type:BAGG - Bridge-Aggregation, RAGG - Route-AggregationAggregation Mode: S - Sic, D - DynamicLoadsharing Type: Shar - Loadsharing,Actor System ID: 0 x8000, 3ce5-a636-3233S -LoadsharingAGGerfaceAGGModePartner IDSelect UnselectPortsPortsShareTypeBAGG1R2disp linSe20SharR2disp link-aggregation vR2d

18、isp link-aggregation vereLoadsharing Type: Shar - Loadsharing,Port Sus: S - Selected, U - UnselectedS -LoadsharingFlags:A - LACP_Activity, B - LACP_Timeout, C - Aggregation,D - Synchronization, E - Collecting, F - Distributing, G - Defaulted, H - ExpiredAggregationerface: Bridge-Aggregation1Aggregat

19、ion Mode: SicLoadsharing Type: SharPortSusPriorityOper-KeyGE1/0/1GE1/0/2SS327683276811PS：只要端口和聚合口的配置相同，就可以聚置接口功，可以不分先配置接口還是先加入聚合再配使用模擬器配置時，可以配置成功，但是網段不能互通配置步驟1、 先創建聚合口，2、 將需要聚合的端口加入聚合組3、 在聚合接口中配置參數，會自動同步給所屬接口故障點1、 未創建聚合端口，disp link-aggregation summary 查看是否創建以及加入的端口數量，是否為激活狀態等2、 端口未加入聚合組，disp link-ag

20、gregation ver操作 key，聚合類型等3、 端口配置與聚合組配置不同，display cure 查看加入聚合組的端口，端口是否激活，erface 進行比對VRRP 綜合實驗中間無心跳線拓撲要求sw4 時，sw2 與 sw3 為其提供虛擬冗余網關PC1PC1 屬于 vlan10，網段 /24，PC2 屬于 vlan20，網段 /24配置Sw1 與 sw2、sw3 之間相連的接口都配置為 trunk，允許 vlan10、20 通過心跳走 sw2sw1sw3配置 ospf，可以學到 sw4 的外部路由Sw1#vlan 10 #vlan 20 #erface GigabitEthernet

21、1/0/2 port link-mode bridgeport link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20#erface GigabitEthernet1/0/3 port link-mode bridgeport link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20# #erface GigabitEthernet1/0/31port link-mode bridgeport acs vlan 1

22、0#erface GigabitEthernet1/0/32port link-mode bridgeport acs vlan 20sw2#router id #net server enable#vlan 1 #vlan 10 #vlan 20 #vlan 100#erface Vlan-erface10ip address 52 vrrp vrid 1 virtual-ip 54vrrp vrid 1 priority 120vrrp vrid 1 trackerface Vlan-erface100 reduced 30vrrp vrid 1 authentication-mode m

23、d5 cipher $c$3$e7perW9GGBC+9j7qcut2e+Dn8wXWxI8T#erface Vlan-erface20ip address 52 ospf cost 20vrrp vrid 2 virtual-ip 54vrrp vrid 2 authentication-mode md5 cipher $c$3$p9xuVvRgvfEf/g4EkCs0fQxPJIUuzNdU#erface Vlan-erface100ip address #erface GigabitEthernet1/0/1port link-mode bridge port link-type tru

24、nkundo port trunk permit vlan 1port trunk permit vlan 10 20#erface GigabitEthernet1/0/3port link-mode bridge#erface GigabitEthernet1/0/4port link-mode bridgeport acs vlan 100#ospf 1 silent- silent-erface Vlan-erface10erface Vlan-erface20area network network 52 network 52 sw3router id #net server ena

25、ble#acl number 2000rule 0 permit source 0#vlan 1 #vlan 10 #vlan 20 #vlan 200#erface Vlan-erface10ip address 53 ospf cost 10vrrp vrid 1 virtual-ip 54vrrp vrid 1 authentication-mode md5 cipher $c$3$qr7GPlJq2QCVIk8zcj1tRDzkLR5axgYj#erface Vlan-erface20ip address 53 vrrp vrid 2 virtual-ip 54vrrp vrid 2

26、priority 120vrrp vrid 2 trackerface Vlan-erface200 reduced 30vrrp vrid 2 authentication-mode md5 cipher $c$3$cnuwOt3jcCWynWWHw/OXHXfyM2Z/NYnT#erface Vlan-erface200ip address #erface GigabitEthernet1/0/1port link-mode bridge port link-type trunkundo port trunk permit vlan 1port trunk permit vlan 10 2

27、0erface GigabitEthernet1/0/4port link-mode bridgeport acs vlan 200#ospf 1 silent- silent-erface Vlan-erface10erface Vlan-erface20area network network 53 network 53 sw4#erface Loack0ip address 55#erface Loack1ip address 55#erface Vlan-erface1ip address dhcp-alloc cnt-identifier mac Vlan-erface1#erfac

28、e Vlan-erface100ip address #erface Vlan-erface200ip address #erface GigabitEthernet1/0/2port link-mode bridgeport acs vlan 100#erface GigabitEthernet1/0/3port link-mode bridgeport acs vlan 200#ospf 1import-route direct area network 55network network 2、中間有心跳線MSTP 模式要求通過 mstp 模式實現負載分擔，配置兩個業務 vlan，配置兩個

29、實例，sw2 與 sw3 分別為實例主根vrrp 通告報文走 sw2sw3，當中間鏈路斷掉之后，走 sw2sw1sw3sw2 與 sw3 之間為鏈路聚合Sw1#stp region-configuration region-name test instance 1 vlan 10instance 2 vlan 20active region-configuration#stp bpdu-protection stp enable#erface GigabitEthernet1/0/31port link-mode bridgeport acs vlan 10stp edged-port ena

30、ble#erface GigabitEthernet1/0/32port link-mode bridgeport acs vlan 20stp edged-port enablesw2#stp region-configuration region-name test instance 1 vlan 10instance 2 vlan 20active region-configuration#stp instance 1 root primary stp instance 2 root secondary stp enable#erface Bridge-Aggregation1 port

31、 link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20#erface GigabitEthernet1/0/2port link-mode bridge port link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20port link-aggregation group 1#erface GigabitEthernet1/0/3port link-mode bridge port link-type trun

32、kundo port trunk permit vlan 1port trunk permit vlan 10 20 port link-aggregation group 1#erface GigabitEthernet1/0/4port link-mode bridgeport acs vlan 100stp disable#Sw3#stp region-configuration region-name test instance 1 vlan 10instance 2 vlan 20active region-configuration#stp instance 1 root seco

33、ndary stp instance 2 root primary stp bpdu-protectionstp enable#erface Bridge-Aggregation1 port link-type trunkundo port trunk permit vlan 1port trunk permit vlan 10 20#erface GigabitEthernet1/0/2port link-mode bridge port link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20port

34、 link-aggregation group 1#erface GigabitEthernet1/0/3port link-mode bridge port link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20port link-aggregation group 1#erface GigabitEthernet1/0/4port link-mode bridgeport acs vlan 200stp disable#Psvrrp 提供冗余網關，mstp 提供二層冗余鏈路，mstp 不隨 vrrp

35、 切換而切換當 vlan10 的網關切換為 sw3 時，實例 1 主根仍為 sw2，數據流量為 sw1sw2sw3sw4將 backup 的接口 cost 改大，影響選路中間為 3 層線路Sw2#Vlan 30 #erface Vlan-erface30ip address 52 #erface Bridge-Aggregation1 port link-type trunkundo port trunk permit vlan 1port trunk permit vlan 10 20 30#ospf 1network 52 sw3#Vlan 30 #erface Vlan-erface30

36、ip address 53 #erface Bridge-Aggregation1port link-type trunkundo port trunk permit vlan 1 port trunk permit vlan 10 20 30#ospf 1network 53 ps中間添加一條三層鏈路后，提供了一條三層冗余鏈路，可以在 sw2 與 sw3 之間交換路由信息,給三層鏈路兩端配置較高的 cost 值，可以防止出現等價路由，影響選路模擬器做 vrrp 時，心跳線路不能切換到下行線路，否則出錯，另外通告時間也得修改，否則頻繁切換故障排除VRRP 配置不是很復雜，如果功能不正常，基本可

37、以通過查看配置以及調試信息來定位。以下，就如何排除常見的故障加以說明。故障之一：控制臺上頻頻給出配置錯誤的提示這表明收到一個錯誤的 VRRP 報文，一種可能是備份組內的另一臺路由器由于配置不一致造成的，另一種可能是有的機器試圖發送的 VRRP 報文。對于第一種可能，可以通過修改配置來解決。對于第二種可能，則是有些機器有不良企圖，應當通過非技術來解決。故障之二：同一個備份組內出現多個 Master 路由器這分為兩種情況，一種是多個 Master 并存時間較短，這種情況是正常的。無需進行人工干預。另一種是多個 Master 長時間共存，這很有可能是由于 Master 之間收不到 VRRP 報文，或

38、者收到的報文不合法造成的。解決的方法是，先互相在多個 Master 之間互相，如果不通，則是其它問題。如果能通，則一定是配置不同造成的，對于同一個 VRRP 備份組的配置，必須要保證虛擬 IP地址個數、每個虛擬 IP 地址、定時器間隔時間和認證方式完全一樣。故障之三：VRRP 的狀態頻繁轉換這種情況一般是由于備份組的定時器間隔時間（adver-erval）設置太短造成的，加大這個時間間隔或者設置搶占延遲都可以解決這種故障。在進行 VRRP 組相關配置之前，需要先在全局模式下配置 vrrp-enable 命令，開啟 VRRP組虛地址使能功能。如果已經配置 VRRP 組，則必須先刪除相應的 VRR

39、P 組，再開啟 vrrp-enable 功能，此時-enable 功能才能生效。vrrp 報文只在 vlan 中發送和接收，不通過三層接口ospf 發布某一個接口，然后將其靜默后，該接口路由還是可以發布出去，只是不能建立鄰居交換其他 lsavrrp 的建立必須兩者之間 vlan 相同，vrid 相同無法vrrp，開啟vrrp-enable 功能故障點1、 未配置 vrrp 或 vrid 配置有誤，virtual-ip 配置錯誤，優先級配置錯誤，time 配置錯誤，驗證配置錯誤，track 上行接口配置有誤，display vrrp ver 2、 出現多個 master，主備之間不能交互 vrr

40、p 報文，可互置，接口是否允許 vlan 通過e 進行比對測試，如不通，檢查線路配PPPPPP 驗證拓撲圖：排錯：debugging ppp pap alldebugging ppp chap all提示驗證失敗，檢查驗證配置ppp pap 單向驗證主驗證方：local-user r2 password simple test service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode papip address 被驗證方：erfaerial0/1/0link-protocol pppppp pap local-

41、user r2 password simple test ip address ppp pap 雙向驗證主驗證方：local-user r2 password simple test service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode papppp pap local-user r1 password simple test2 ip address 被驗證方：local-user r1password simple test2 service-type ppperfaerial0/1/0link-prot

42、ocol pppppp authentication-mode papppp pap local-user r2 password simple test ip address CHAP 單向驗證a、主驗證方不在接口配置用戶名主驗證方：local-user r2 password simple test service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode chapip address 被驗證方：erfaerial0/1/0link-protocol pppppp chap user r2ppp chap

43、password simple testip address b、主驗證接口配置用戶名ps：接口配置對端本地配置的用戶名，主驗證方：local-user r2password simple test要求相同service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r1ip address 被驗證方：local-user r1 password simple test service-type ppperfaerial0/1/0link-protocol pppppp cha

44、p user r2ip address CHAP 雙向認證ps：本端接口配置的用戶名和都與對端本地配置的用戶名相對應a、雙接口都配置用戶名，可以不同r1 端：local-user r2 password simple test service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r1ppp chap password simple test2 ip address r2 端：local-user r1password simple test2 service-type

45、 ppperfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r2ppp chap password simple testip address b、雙接口只配置用戶名，必須相同r1 端：local-user r2 password simple test service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r1ip address r2 端：local-user r1 pa

46、ssword simple testservice-type ppperfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r2ip address ppp mpps：驗證配置在物理接口上，驗證方式可隨意選擇將鏈路直接綁定到 VT 上r1 端：local-user r2 password simple test service-type ppp#erface Virtual-Template1ip address erfaerial0/1/0link-protocol pppppp authentica

47、tion-mode chap ppp chap user r1ppp mp Virtual-Template 1#erfaerial0/1/1link-protocol pppppp authentication-mode chap ppp chap user r1ppp mp Virtual-Template 1RT1-Serial0/1/1disp ppp mpTemplate is Virtual-Template1 max-bind: 16, min-fragment: 128Bundle 52543214/r2, 2 members, Master link is Virtual-T

48、emplate1:0Peers endPodescriptor: 52543214Sequence format: long/long rcv/sentBundle Up Time: 2013/06/0323:04:18:333 0 lost fragments, 5 reordered, 0 unassigned, 0 Sequence: 4/5 rcvd/sentThe member channels bundled are:erleavedSerial0/1/0Serial0/1/1Up-Time:2013/06/03Up-Time:2013/06/0323:04:18:33323:04

49、:49:174r2 端：local-user r1 password simple test service-type ppp#erface Virtual-Template1ip address erfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r2ppp mp Virtual-Template 1#erfaerial0/1/1link-protocol pppppp authentication-mode chap ppp chap user r2ppp mp Virtual-Template

50、 1RT2disp ppp mpTemplate is Virtual-Template1 max-bind: 16, min-fragment: 128Bundle 52543114/r1, 2 members, Master link is Virtual-Template1:0Peers endPodescriptor: 52543114Sequence format: long/long rcv/sentBundle Up Time: 2013/06/0323:04:18:882 0 lost fragments, 0 reordered, 0 unassigned, 0 Sequen

51、ce: 0/0 rcvd/sentThe member channels bundled are:erleavedSerial0/1/0Serial0/1/1Up-Time:2013/06/03Up-Time:2013/06/0323:04:18:88223:04:49:707按用戶名找 VTr1 端：local-user r2 password simple test service-type ppp#erface Virtual-Template1ip address ppp mp user r2 bind Virtual-Template 1erfaerial0/1/0link-prot

52、ocol pppppp authentication-mode chap ppp chap user r1ppp mp#erfaerial0/1/1link-protocol pppppp authentication-mode chap ppp chap user r1ppp mpRT1disp ppp mpTemplate is Virtual-Template1 max-bind: 16, min-fragment: 128Bundle 52543214/r2, 2 members, Master link is Virtual-Template1:0Peers endPodescrip

53、tor: 52543214Sequence format: long/long rcv/sentBundle Up Time: 2013/06/0323:09:05:2030 lost fragments, 0 reordered, 0 unassigned, 0 Sequence: 0/0 rcvd/sentThe member channels bundled are:erleavedSerial0/1/0Serial0/1/1 r2 端：local-user r1 password simple test service-type ppp#erface Virtual-Template1

54、ip address Up-Time:2013/06/03Up-Time:2013/06/0323:09:05:20323:09:09:399ppp mp user r1 bind Virtual-Template 1erfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r2ppp mp#erfaerial0/1/1link-protocol pppppp authentication-mode chap ppp chap user r2ppp mpRT2disp ppp mpTemplate is

55、Virtual-Template1 max-bind: 16, min-fragment: 128Bundle 52543114/r1, 2 members, Master link is Virtual-Template1:0Peers endPodescriptor: 52543114Sequence format: long/long rcv/sentBundle Up Time: 2013/06/0323:09:05:767 0 lost fragments, 0 reordered, 0 unassigned, 0 Sequence: 0/0 rcvd/sentThe member

56、channels bundled are:erleavedSerial0/1/0Serial0/1/1Up-Time:2013/06/0323:09:05:767Up-Time:2013/06/0323:09:09:948將鏈路綁定到 MP-group 接口r1 端：local-user r2 password simple test service-type ppperfaerial0/1/0link-protocol pppppp authentication-mode chap ppp chap user r1ppp mp Mp-group 1#erfaerial0/1/1link-pr

57、otocol pppppp authentication-mode chap ppp chap user r1ppp mp Mp-group 1erface Mp-group1ip address RT1-Serial0/1/1disp ppp mpMp-group is Mp-group1max-bind: 16, min-fragment: 128Bundle Multilink, 2 members, Master link is Mp-group1Peers endPodescriptor: Mp-group1Sequence format: long/long rcv/sentBun

58、dle Up Time: 2013/06/0323:13:21:247 0 lost fragments, 0 reordered, 0 unassigned, 0 Sequence: 0/0 rcvd/sentThe member channels bundled are:erleavedSerial0/1/0Serial0/1/1 r2 端：local-user r1 password simple testservice-type pppUp-Time:2013/06/0323:13:21:247Up-Time:2013/06/0323:13:27:815erfaerial0/1/0li

59、nk-protocol pppppp authentication-mode chap ppp chap user r2ppp mp Mp-group 1#erfaerial0/1/1link-protocol pppppp authentication-mode chap ppp chap user r2ppp mp Mp-group 1erface Mp-group1ip address RT2disp ppp mpMp-group is Mp-group1max-bind: 16, min-fragment: 128Bundle Multilink, 2 members, Master

60、link is Mp-group1Peers endPodescriptor: Mp-group1Sequence format: long/long rcv/sentBundle Up Time: 2013/06/0323:13:21:796 0 lost fragments, 0 reordered, 0 unassigned, 0 Sequence: 0/0 rcvd/sentThe member channels bundled are:erleavedSerial0/1/0Serial0/1/1Up-Time:2013/06/03Up-Time:2013/06/0323:13:21: