1、KPI指標分析與處理 2005年5月切換成功率公式1切換成功率公式2KPI指標公式KPI指標公式無線接通率公式1無線接通率公式2KPI指標公式全網掉話率公式1全網掉話率公式2KPI指標監測OMCR自定義PM監測模板 觀察全網KPI指標情況，收集并排序小區級KPI指標，分析掉話最高或擁塞最嚴重的的510個小區，定位故障原因，派發排障工單。利用GETPM工具利用MotoANS系統。檢查掉話小區是否連接有直放、功放等設備檢查掉話在該小區的載頻上分布情況檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等） PB2或奇偶值 IOI5或單個載頻明顯偏高利用Perf工具過

2、濾Ma_fail_from_ms高的載頻檢查掉話小區的周圍小區是否存在斷站情況檢查掉話小區周圍基站是否擁塞嚴重高掉話小區處理思路RF掉話小區內切換掉話檢查掉話小區是否連接有直放、功放等設備檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等）利用Perf工具過濾Ma_fail_from_ms高的載頻檢查掉話小區的周圍小區是否存在斷站情況檢查掉話小區周圍基站是否擁塞嚴重檢查切換參數設置是否合理高掉話小區處理思路切換掉話高掉話小區處理思路切換掉話BSC內部切換掉話檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等）統計其鄰區的I

3、N_INTRA_BSS_HO_RETURN值檢查上述統計項（切入返回）高的小區的Per Carrier統計項。打開Per Neighbour的統計項，檢查切向哪個鄰區的成功率較低檢查掉話小區的周圍小區是否存在斷站情況檢查掉話小區周圍基站是否擁塞嚴重檢查切換參數設置是否合理和周圍小區有無同BCCH、BSIC的小區 BSC之間切換掉話檢查掉話小區的Per Carrier統計項（Path_balance、BER、IOI等）檢查鄰區切換信息如LAC、Cell ID、BCCH、BSIC等設置是否有誤統計其鄰區的IN_INTRA_BSS_HO_RETURN值檢查上述統計項（切入返回）高的小區的Per Ca

4、rrier統計項。打開Per Neighbour的統計項，檢查切向哪個鄰區的成功率較低檢查掉話小區的周圍小區是否存在斷站情況檢查掉話小區周圍基站是否擁塞嚴重檢查切換參數設置是否合理和周圍小區有無同BCCH、BSIC的小區高掉話小區處理思路切換掉話RF掉話相關參數上行（Up link) LINK_FAIL：不能解碼減1，恢復加2；變?yōu)?，停止發射 LINK_ABOUT_TO FAIL：確定BTS、MS何時滿功率發射 T3109：釋放TCH參數 下行（Down link) RADIO_LINK_TIMEOUT ：不能解碼減1，恢復加2；超時MS停止發射 T3109必須大于Radio_link_ti

5、meout，防止兩個手機同時占用同一個TCH信道產生串話現象FULL_PWR_RF_LOSS設置為1 切換類型和優先級別Uplink qualityUplink interferenceDownlink qualityDownlink interferenceUplink rxlevDownlink rxlevDistancePBGT由高到低切換參數設置averagingHreqave = 3Hreqt = 3-85-88-88-91-91-89-88-86-87-96-95-94-94-92-91-91N = 3P = 2-90.3-88-86-88.3-87-91-89.3-87.7-91

6、-90.3-88-91.7表示多少個采樣點進行平均表示保留多少個平均值Averaging :注意:N=Hreqt Hreqave*Hreqt=32切換參數設置averagingHreqave/Hreqt的設置參數修改命令格式chg_cell_element rxqual_dl_ho, 0 0 4 6 0 0 0 LAC CellIDEnter hreqave: 4Enter hreqt: 3 Enter w_qual: 1 參數查看命令格式disp_element rxqual_dl_ho, 0 37 cell_number =4 6 0 0 0 31122 4153rxqual_dl_ho0

7、 = alg_num: 0 alg_data: 4 3 0切換參數設置Rxqual下列參數設置決定是否做RXqual切換：ul_rxqual_ho_allowed : 上行RXqual切換控制開關dl_rxqual_ho_allowed : 下行RXqual切換控制開關chg_cell_element rxqual_dl_ho, 0 0 4 6 0 0 0 LAC CELLIDchg_cell_element rxqual_ul_ho, 0 0 4 6 0 0 0 LAC CELLIDdecision_1_n6/decision_1_p6：滿足切換門限的測量報告數目 （經過平均過的）大于等于P

8、6 l_rxqual_dl_h： RXqual切換控制門限 l_rxqual_ul_h：命令格式 chg_element decision_1_n1 切換參數設置Interference下列參數設置決定是否做RXqual切換：.interfer_ho_allowed : 切換開關chg_cell_element rxlev_ul_ho, 0 0 4 6 0 0 0 LAC CELLIDchg_cell_element rxlev_dl_ho, 0 0 4 6 0 0 0 LAC CELLID N7 must be greater than or equal to P7. N7 must be

9、less than or equal to the hreqt value set using chg_cell_element rxlev_ul_ho command for rxlev_dl_ho andrxlev_ul_ho.decision_1_n7/decision_1_p7thresholds: u_rxlev_dl_ih/u_rxlev_ul_ih 切換門限 interfer_ho_allowed 開關參數 intra_cell_handover_allowed 開關參數chg_cell_element rxqual_ul_ho, 0 0 4 6 0 0 0 LAC CELLID

10、 chg_cell_element rxqual_dl_ho, 0 0 4 6 0 0 0 LAC CELLID chg_cell_element rxlev_ul_ho, 0 0 4 6 0 0 0 LAC CELLID chg_cell_element rxlev_dl_ho, 0 0 4 6 0 0 0 LAC CELLID n6/p6 n7/p7 判決條件 u_rxlev_ul_ih/u_relev_dl_ih l_rxqual_ul_h/u_rxqual_dl_h 切換門限 hop_count 切換次數 hop_count_timer 時間（SACCH）切換參數設置Intracell

11、切換參數設置PBGT pwr_handover_allowed 開關參數 Use_neighbor_pbgt_hreqave1=use hreqave in add_nei0=use hreqave in add_cell PBGT(n) ho_margin_cell 切換門限切換參數設置擁塞釋放ho_exist_congestmb_tch_cong_threscongest_ho_margin bounce_protect_margin bounce_protect_cong_tmr If there is no free TCH available when an assignment r

12、equest is coming in, it is possible to handover existing calls to neighbor cells and free TCHs for new coming callsIf ho_exist_congest = 1, handover as many calls as the number of queued assignment requestsIf ho_exist_congest = 2, handover as many calls as that meet congestion relief criteria切換參數設置

13、其它en_incom_ho enable incoming handoverinter_cell_handover_allowedms_distance_allowed : enable distance handover decision_1_n8/decision_1_p8 thresholds: ms_max_range the ms_max_range is also used by RRSM to reject Channel Requests from distant mobiles. This feature is enabled by chg_element poor_init

14、ial_assignmentbounce_protect_margin bounce_protect_qual_tmr功率控制RXqualThe following parameters will determine if the power control has to be done due to rxqual.for power increase: decision_1_n3/decision_1_p3for power decrease: decision_1_n4/decision_1_p4uplink thresholds: l_rxqual_ul_p/u_rxqual_ul_pd

15、ownlink thresholds:l_rxqual_dl_p/u_rxqual_dl_p功率控制RxlevThe following parameters will determine if the power control has to be done due to rxlev.for power increase: decision_1_n1/decision_1_p1for power decrease: decision_1_n2/decision_1_p2uplink thresholds: l_rxlev_ul_p/u_rxlev_ul_pdownlink threshold

16、s: l_rxlev_dl_p/u_rxlev_dl_p功率控制參數MSms_power_control_allowedenable/disable MS power control, if disabled, the MS transmits in max_tx_ms.ms_p_con_interval (0-31 , 1 step= 2 SACCH multiframes,default=2)the minimum time in BSS interval between successive power control commands.ms_p_con_ack (0-31 , 1 st

17、ep= 2 SACCH multiframes,default=2) when the MS is sent a new power control message, it will change transmit power and then echoes an ack message. The ms_p_con_interval will only be started when ack has been received or this timer has expired.功率控制BTSbts_p_con_intervalbts_p_con_ackfor BTS power contro

18、l, same as the previous one.bts_power_control_allowedif disable, the BTS transmits in max_tx_bts功率控制步長pow_inc_step_size_ulpow_inc_step_size_dlsets the step size for uplink and downlink power increase in dBpow_red_step_size_ulpow_red_step_size_dlsets the step size for uplink and downlink power decrease in dB功率控制rapid pwr downrapid_pwr_downenable/disable