1、Calvin Wang 08-9-25,Product Introduction of Power Steering Pump,液壓助力轉向泵產品簡介,Application in Vehicle,Application in Vehicle,Pump Function,Minimum output: 2.27 L/Min flow at 465 RPM against 4.585.07 MPa pressure低流量 2.27 L/Min (465 RPM, 4.585.07 MPa)，發動機怠速時提供一定的轉向助力 Maximum output: 7.458.85 L/Min flow a

2、t 1500 RPM against 0.35 MPa pressure高流量 7.458.85 L/Min (1500 RPM, 0.35MPa)，發動機正常運轉時提供恒定的轉向助力 Relief pressure: 95105 MPa at 1500 RPM泄壓值 95105 MPa (1500 RPM)，當方向盤打死或轉到極限位置，保護HPS系統,Pump Function,Pump Function,Pump Function,Pump Function,Pump Structure,Pump Structure,Pump Structure,Pump Type,Pump Type,P

3、ump Type,Pump Type,Pumps Rapid Response,Minor modifications to pump components can vary displacement, high rpm flow rate, relief pressure, and mounting configuration 根據客戶的要求(低流量、高流量、泄壓值與安裝位置等）Power Steering Pump團隊能作出快速反應，并再原有產品基礎盡量減少更改,Pumps DV/PV Test,注 ： DV (Design Validation) test for prototype s

4、ample 即手工樣件設計驗證 PV (Process Validation) test for OTS sample 即OTS樣件驗證,Durability test 耐久性測試 - To confirm deterioration after long operating 確認長時間運行之后功能下降或喪失 - Including sealing parts, springs, wear of sliding surface 包括密封件、彈簧、摩擦面 Special test for vital mode 關鍵實效模式測試 - To confirm what condition occur

5、vital failure 確認在什么情況下會發生關鍵的性能實效 - Seizure test, cold start test, high temp test, high pressure test, high belt load test, etc 卡死測試、冷啟動測試、高溫測試、高壓測試、皮帶輪受載測試等 Breakage test 破壞性試驗 - To verify the safety factor on strength of each parts 驗證零件在強度方面的安全性能,Pumps Localization,1. Localized: Housing, Pulley, Re

6、turn Tube, Pressure Plate, Thrust Plate 2. To be localized: End Cover, Drive Shaft, Standard-Flow Fitting, Valve 3. Plan to be localized: Ring, Rotor 4. Left: Spring Parts, Sealing Parts, Pin, Vane,Pumps Problem at Present,1. Leakage: You may find oil drop after parking and abnormal noise if too much leaking 泄漏（現有檢測設備氣密性測試） 2. Noisy: You catch abnormal noise when turn the wheel 噪音（現有檢測設備STC噪音測試） 3. Heavy steeling: It is too hard to turn wheel and you