1、XXXX紙業集團股份有限公司銅版紙工廠動力車間名稱 PASABAN切紙機默樂卡速度設定作業指導書修訂時間20081016版本 01編號TBZWC14頁數3適用范圍傳動完成專業一、需用工具：小平口螺絲刀或電筆二、具體內容：Use a small screwdriver to move the two selectors labeled H and L, located at the top， to 0，with the power supply switched off將電源開關關閉，用小螺絲刀將底座上標有H和L撥到0位置Re-establish the power to the WINbloc

2、 I/O module. The default speed value or transmission ratio for the WINbloc I/O modules is 125 kBit/s and is saved in series EEPROM. This process is indicated for 5 seconds, during which the red BF LED flashes on and off (flashing frequency: 2 Hz)給I/O卡重新上電。以默認速度或者125kBit的速度發送參數，并且保存在EEPROM內。這個過程大約需要5

3、秒，在這期間，BF指示燈將自動閃爍（頻率2HZ）During the 5 seconds for which the LED flashes on and off, the H selector should be set to F and the L selector left alone (I. e. set. to 0), in order to initiate the programming of the transmission speed or ration.BF指示燈自動閃爍的時候，將高位選擇器調節到F上，低位選擇器依舊。為了設定傳送的速度As soon as the red

4、BF led stops flashing, the user has 10 seconds in which to select a transmission speed value or ratio of between o and 8, in accordance with the table given below. To do this, simply move the L selector to anywhere between 0 and 8, depending on the value required. In this way, at the end of the 10 s

5、econds interval, the module should have a value of between F0h and F8h.當紅色BF燈停止閃爍，用戶有十秒鐘時間從0至8之間來選擇與給定值一致的傳輸速度值, 來做這一步, 只是將 L 選擇者設為 0 和 8之間某一值，此值取決于需求值。同樣，在最后10秒時間內，模塊將被設定為在F0至F8之間的某個值。Index012345678Bit rate (kBit)1000800500250125100502010The BF LED will flash (at a frequency of 1 Hz) to confirm tha

6、t the transmission index has been selected. The LED will flash between 0 and 8 times, depending on the selected value.指示燈將閃爍來確認被選擇的傳輸速率。 BF 引導將會閃現 ( 在一周率 1個赫茲) 確定傳動分度已經被選擇。 那指示燈將會在 0 和 8 次之間閃現,根據選擇的值。The red BF LED will flash on and off (frequency: 5 HZ) for 5 seconds in order to confirm that the pr

7、ogramming has been completed.指示燈將閃爍5秒來確認設定過程結束。Once the process has been completed, the value is recorded in series EEPROM and will be the value which will remain in the said module. If the communications speed needs to be changed once again, the value can only be altered by following the same configuration process as tha