粗紗條干不勻率的檢測與控制產品的質量標準半制品質量控制織物質量控制棉紗質量標準與檢驗紗線質量控制目錄粗紗條干不勻率控制范圍01粗紗條干不勻率檢測02粗紗條干不勻率控制措施03CONTENTS目錄檢測粗紗條干不勻率的意義粗紗條干不勻率與成紗條干不勻率顯著相關，對布面條干和紗疵影響極大，與成紗重量不勻率、強力不勻率也有相當?shù)年P(guān)聯；另外，檢測粗紗的條干不勻率可以及時發現質量隱患，可以減少紗疵、提高產品質量。粗紗重量不勻率控制范圍紡紗類型純棉精梳紗化纖混紡紗特細特、細特紗中特紗粗特紗粗紗條干不勻率（%）6.9~9.56.5~9.16.1~8.74.5~6.84.5~6.8粗紗條干不勻率控制措施粗紗條干不良的影響因素：搖架加壓的彈簧失效、斷裂，固定螺釘松動，調節螺釘走動；搖架腳抓握持不良，膠圈銷歪斜，膠輥與羅拉不平行；上下膠圈過緊或過松，膠圈走偏、龜裂或無膠圈紡紗；上下銷鉗口隔距過小或過大；羅拉隔距過小或過大；部分牽伸配置不當，或粗紗伸長率太大；膠輥嚴重中凹，表面嚴重?fù)p壞，膠輥軸承缺油、損壞；嚴重的纏羅拉、膠輥，使羅拉彎曲、隔距走動，并影響同檔加壓的相鄰錠子的粗紗條干；牽伸齒輪爆裂、偏心、缺齒、鍵與鍵槽松動、鍵磨損或齒輪嚙合不良；上下膠圈偏移太大，隔距塊碰下膠圈；喂入棉條條干嚴重不勻，打褶或附有飛花；粗紗捻度過大或過小。錠翼嚴重?fù)u頭；集合器不符要求、破損、軋煞或跳動；車間相對濕度過低，粗紗回潮率在6%以下；棉條跑出膠輥控制范圍。措施：加強牽伸、加壓、集合、喂入部件檢修；正確設計工藝及工藝上機檢查；正確加捻；防止意外牽伸；控制前道熟條質量；注意控制車間溫濕度，純棉普梳粗紗條干CV(%)粗紗定量（g/10m）條干CV值（%）5%25%50%75%95%14.84.335.055.826.777.9811.84.475.165.936.857.999.84.585.266.036.927.998.44.685.346.106.988.007.44.765.426.177.048.006.64.845.486.237.088.015.94.915.546.297.128.015.44.975.606.347.168.024.95.035.656.397.208.024.55.095.706.437.238.024.25.145.746.477.268.033.95.195.786.517.298.033.75.245.826.547.318.033.55.285.856.587.348.033.35.325.896.617.368.04純棉精梳粗紗條干CV(%)粗紗定量（g/10m）條干CV值（%）5%25%50%75%95%4.93.213.624.074.625.384.53.233.644.094.635.384.23.253.654.104.645.393.93.273.674.114.665.393.73.283.684.124.675.393.53.313.694.134.685.393.33.333.714.144.685.403.13.333.724.154.695.403.03.343.734.154.705.402.83.353.744.164.715.402.73.363.754.174.725.412.63.373.764.184.725.412.53.383.764.1