1、CHECK RESULT 檢查結果OK.RATIOTitle 項目Part codeP1P2P3TOTAL全尺寸OK Ratio100%OK Pos31Total Pos31SURF.型面OK Ratio100%OK Pos15Total Pos15TRIM修邊OK Ratio100%OK Pos13Total Pos13HOLE孔位孔徑OK Ratio100%OK Pos3Total Pos3Title 項目Content 內容CS11_Fully measured ReportProject Name 項目名稱CS11Part Code 零件號CAD NumberCAD 號-011Part

2、 Name 零件名稱HINGE REINFORCEMENT LOWER RR LHTie1r 供應商Toolingr 模具供應商tianyueMaterial standard code 板材牌號VDA 239-CR240LAActual Material 替代牌號Thickness 板材厚度1.2Coating thickness 鍍鋅層厚度GI50/50-UDetection time 檢測日期2016.12.15RPS InformationStep 1 : MP CheckingStep 2 : Surface CheckingStep 3 : Trim CheckingStep 4

3、: Hole size CheckingJ1SD990H4LSD910H1Lnominal10.+0.15/-010.0+0.22/-08.0+0.22/-0actual10.1310.178.16deviation.Step 5 : ThinningREPORT CHECKING THINNESMeasure thickness request: 1.2 mmactual thickness 1.20mmLIMITS MAX : 20%11.163.3%21.154.2%31.172.5%41.181.7%51.172.5%61.163.3%71.181.7%8910111213141516

4、THINNING MAXStep 6 : Appearance CheckingAppearance Checking 外觀檢查NO判定標準 Control standard檢驗方法 Methond判定 OK、NG、N/APicture1零件是否正確？ Is the rignt part?Visual目視OK2變薄率是否 料厚的 20%范 內？ THINNING MAX no more 20%Venire caliper 游標卡尺OK3是否有開裂、暗裂？ No crack,deformationVisual目視OK4毛邊、毛刺、尖角是否 0.3mm 范圍內？ glitches, indenio

5、n,damaged,Venire caliper 游標卡尺OK5是否有模痕、壓傷（無手感可接受）？ No roughness detect with the handwith the handOK6是否有拉傷、劃傷？No degradation or deformation手觸 with the handOK7是否有起皺、變形（裝配面平面度需 0.2MM 以?xún)?nèi)）？No crack,deformationVisual /Venire caliper目視/游標卡尺OK8是否有生銹？Rust?Visual目視OK9字印是否正確、明顯且無手 感？Marking information crrect ?Visual/ with the hand目視/手觸OK10公差是否與 3D 公差相符？ Report tolerance is the same with 3D?檢查 checkingOK11零件定位是否與檢具定義相符？ PRS is the same with gauge?檢具 gaugeOK12料邊斷差是否超過公差帶的 50%？ Trim no moren 50% out of tolerance